Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "The difference between the trace of a line and the trace of a plane"
Teach me: 1. Identify the types of lines used in technical drawing and the purpose and weight of each
You are my personal SS1 Technical Drawing tutor. Teach me 1. Identify the types of lines u
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allPractice set: Enlarge and reduce plane figures based on the ratio of areas and verify the result
Set me five practice tasks on enlarge and reduce plane figures based on the ratio of areas
Subscribe to unlock allPractice set: Demonstrating and carry out the construction of plane figures of equal area
Set me five practice tasks on demonstrating and carry out the construction of plane figure
Subscribe to unlock allQuiz: 2. Determine the true length of a line by rotation and by auxiliary projection
Set me a quick recall test on 2. Determine the true length of a line by rotation and by au
Subscribe to unlock allWAEC prep: Success: all letters within ±0.5 mm of the guide-line height with uniform stroke thickness
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allQuiz: 2. Distinguish between enlargement by ratio of sides and by ratio of areas
Quiz me on 2. Distinguish between enlargement by ratio of sides and by ratio of areas, fro
Subscribe to unlock allSpot my mistake: 4. Determine the linear ratio corresponding to a given ratio of areas
Show me a worked example on 4. Determine the linear ratio corresponding to a given ratio o
Subscribe to unlock allQuiz: 2. State the principles of converting the shape of a plane figure into another of equal area
Set me a quick recall test on 2. State the principles of converting the shape of a plane f
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allLet me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock allPractice set: Plotting the loci of a point at a fixed distance from a line
Give me a practice set on plotting the loci of a point at a fixed distance from a line for
Subscribe to unlock allLet me explain: 3. Differentiate between isometric and non-isometric lines
Act as my study partner. I will teach you 3. Differentiate between isometric and non-isome
Subscribe to unlock allTeach me: 1. Define technical drawing in your own words and distinguish the two classifications of drawing
You are my personal SS1 Technical Drawing tutor. Teach me 1. Define technical drawing in y
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allQuiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock all