Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →287 prompts matching "The centroid of a figure with a cut-out"
Practice set: Cutting paper cylinder to show that the seam edge of the development is the stretch-out
Give me a practice set on cutting paper cylinder to show that the seam edge of the develop
Subscribe to unlock allWAEC prep: Determine the true shape of the cut face of a 50 mm diameter cylinder truncated at 30 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Drawing the true shape of the cut face of a square pyramid of 50 mm base truncated at 40
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allTeach me: What is meant by the true shape of a cut surface
You are my personal SS2 Technical Drawing tutor. Teach me what is meant by the true shape
Subscribe to unlock allSpot my mistake: The conic section produced by each of four stated cutting planes on a cone
Write a short SS2 Technical Drawing answer about the conic section produced by each of fou
Subscribe to unlock allQuiz: Determine the true shape of the cut face of a hexagonal prism truncated by an inclined plane
Set me a quick recall test on determine the true shape of the cut face of a hexagonal pris
Subscribe to unlock allLet me explain: Determine the true shape of the cut face of a square pyramid truncated by an inclined plane
I am going to explain determine the true shape of the cut face of a square pyramid truncat
Subscribe to unlock allProject task: Set out the development of their Week 6 truncated cone on card
Give me a practical task on set out the development of their Week 6 truncated cone on card
Subscribe to unlock allPractice set: Arranging three cut-out views on the desk in first angle order
Give me a practice set on arranging three cut-out views on the desk in first angle order f
Subscribe to unlock allPractice set: Comparing their auxiliary outline of the cone
Give me a practice set on comparing their auxiliary outline of the cone for SS2 Technical
Subscribe to unlock allReal-life Nigeria: Lesson with the load path from roof to soil, drawing it as arrows on a board section
Take lesson with the load path from roof to soil, drawing it as arrows on a board section
Subscribe to unlock allWAEC prep: Why an arch is built with an odd number of voussoirs and a keystone at the crown
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Project the true shape of a cut face on a pentagonal pyramid where the cutting plane passes
Give me a wrong or muddled explanation of project the true shape of a cut face on a pentag
Subscribe to unlock allTeach me: Obtain the true shape of the cut face from the auxiliary view
I am an SS2 student studying Auxiliary Views III in Technical Drawing. Explain obtain the
Subscribe to unlock allQuiz: Producing an oblique (cabinet) drawing of the same block with the depth drawn at half scale
Quiz me on producing an oblique (cabinet) drawing of the same block with the depth drawn a
Subscribe to unlock allSpot my mistake: Why the damp-proof course must be continuous with the damp-proof membrane under the floor
Show me a worked example on why the damp-proof course must be continuous with the damp-pro
Subscribe to unlock allWAEC prep: Develop and build in card a truncated cylinder of 50 mm diameter cut at 45 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: The difference between the eccentricity of a parabola and that of a hyperbola
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Drawing the involute of a square of 30 mm side and measure the length of the final arc
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Plotting the locus of the mid-point of the connecting rod for twelve crank positions
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock all