Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Tension and compression members on a board sketch of a king post truss"
Teach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allPractice set: Demonstrating safe handling of board, T-square and compass
Set me five practice tasks on demonstrating safe handling of board, T-square and compass,
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allTeach me: 1. Define technical drawing in your own words and distinguish the two classifications of drawing
You are my personal SS1 Technical Drawing tutor. Teach me 1. Define technical drawing in y
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock allLet me explain: 3. State the properties of regular polygons including interior, exterior and central angles
Act as my study partner. I will teach you 3. State the properties of regular polygons incl
Subscribe to unlock allSpot my mistake: 4. Calculate the interior and exterior angles of any regular polygon
Show me a worked example on 4. Calculate the interior and exterior angles of any regular p
Subscribe to unlock allQuiz: 2. Identify the types of scales: plain, diagonal, comparative and vernier
Set me a quick recall test on 2. Identify the types of scales: plain, diagonal, comparativ
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allLet me explain: 3. Describe the applications of enlargement and reduction in design and manufacture
Act as my study partner. I will teach you 3. Describe the applications of enlargement and
Subscribe to unlock allSpot my mistake: 4. Verify the accuracy of an enlargement by measurement and calculation
Write a short SS1 Technical Drawing answer about 4. Verify the accuracy of an enlargement
Subscribe to unlock allPractice set: Enlarge and reduce plane figures based on the ratio of areas and verify the result
Set me five practice tasks on enlarge and reduce plane figures based on the ratio of areas
Subscribe to unlock allLet me explain: 4. Convert a given irregular polygon into a triangle of equal area and verify by calculation
Act as my study partner. I will teach you 4. Convert a given irregular polygon into a tria
Subscribe to unlock allPractice set: Demonstrating and carry out the construction of plane figures of equal area
Set me five practice tasks on demonstrating and carry out the construction of plane figure
Subscribe to unlock allSpot my mistake: Success: calculated areas of original and converted figures agree within 2%
Show me a worked example on success: calculated areas of original and converted figures ag
Subscribe to unlock allSpot my mistake: 1. State the principle of tangency and its applications
Show me a worked example on 1. State the principle of tangency and its applications with a
Subscribe to unlock allTeach me: 2. Plot the locus of a point on a rotating and a sliding mechanism
Be my SS1 Technical Drawing teacher for this one point: 2. Plot the locus of a point on a
Subscribe to unlock all