Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →287 prompts matching "Success: sides of the heptagon equal within 0.5 mm by at least two of the three"
Let me explain: Constructing the involute of a square and of a regular hexagon of 30 mm side
Act as my study partner. I will teach you constructing the involute of a square and of a r
Subscribe to unlock allWAEC prep: Drawing the involute of a square of 30 mm side and measure the length of the final arc
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allLet me explain: Constructing a parabola inside a given rectangle 100 mm by 60 mm by the intersecting-lines
I am going to explain constructing a parabola inside a given rectangle 100 mm by 60 mm by
Subscribe to unlock allQuiz: Constructing the involute of a circle of 40 mm diameter for one complete revolution
Quiz me on constructing the involute of a circle of 40 mm diameter for one complete revolu
Subscribe to unlock allPractice set: Calculating the stroke of a slider-crank whose crank radius is 30 mm
Set me five practice tasks on calculating the stroke of a slider-crank whose crank radius
Subscribe to unlock allProject task: Drawing the plan and elevation of a 60 mm diameter
Give me a practical task on drawing the plan and elevation of a 60 mm diameter from True S
Subscribe to unlock allWAEC prep: Determine the true shape of the cut face of a 50 mm diameter cylinder truncated at 30 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Drawing the true shape of the cut face of a square pyramid of 50 mm base truncated at 40
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Determine the curve of intersection of two cylinders of equal diameter meeting at 90 degrees
Write a short SS2 Technical Drawing answer about determine the curve of intersection of tw
Subscribe to unlock allTeach me: Determine the curve of intersection of two cylinders of unequal diameter
I am an SS2 student studying Intersection of Solids I in Technical Drawing. Explain determ
Subscribe to unlock allWAEC prep: Determine the curve of intersection of a 30 mm branch entering a 50 mm main cylinder at 90
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allPractice set: Why the curve becomes two straight lines when the two cylinders are of equal diameter
Set me five practice tasks on why the curve becomes two straight lines when the two cylind
Subscribe to unlock allProject task: Determine the intersection of a 30 mm square prism entering a 50 mm hexagonal prism at 60
Give me a practical task on determine the intersection of a 30 mm square prism entering a
Subscribe to unlock allSpot my mistake: Drawing an isometric circle of 40 mm diameter by the four-centre method
Show me a worked example on drawing an isometric circle of 40 mm diameter by the four-cent
Subscribe to unlock allWAEC prep: Drawing the auxiliary plan of a 60 mm high cone on a plane inclined at 45 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allReal-life Nigeria: Drawing the auxiliary plan of a cylinder 50 mm diameter truncated at 40 degrees
Take drawing the auxiliary plan of a cylinder 50 mm diameter truncated at 40 degrees out o
Subscribe to unlock allProject task: LINE, OFFSET, TRIM and ELLIPSE commands on the projector
Give me a practical task on LINE, OFFSET, TRIM and ELLIPSE commands on the projector from
Subscribe to unlock allWAEC prep: The sequence of commands used to obtain the auxiliary view
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Calculating the true length of a line whose plan is 60 mm
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allLet me explain: Sketching freehand front, top and side views of two of the same tools
I am going to explain sketching freehand front, top and side views of two of the same tool
Subscribe to unlock all