Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →287 prompts matching "Success: radius and tangent perpendicular within ±1° at every point of tangency"
Teach me: Drawing the tangent and normal at a stated point on each curve
Be my SS2 Technical Drawing teacher for this one point: drawing the tangent and normal at
Subscribe to unlock allPractice set: What is meant by the first quadrant and why technical drawing works within it
Set me five practice tasks on what is meant by the first quadrant and why technical drawin
Subscribe to unlock allSpot my mistake: Annotate every material with leader lines and complete the sheet with a title block and scale
Write a short SS2 Technical Drawing answer about annotate every material with leader lines
Subscribe to unlock allTeach me: Examined with the command words state, describe and explain
I am an SS2 student studying Loci and Special Curves in Technical Drawing. Explain examine
Subscribe to unlock allReal-life Nigeria: Checking each other's stroke measurement against the calculated value of twice the crank radius
Take checking each other's stroke measurement against the calculated value of twice the cr
Subscribe to unlock allPractice set: Calculating the stroke of a slider-crank whose crank radius is 30 mm
Set me five practice tasks on calculating the stroke of a slider-crank whose crank radius
Subscribe to unlock allTeach me: Assessed AO3, and true shapes of truncated solids are a standing WAEC and NECO question
I am an SS2 student studying True Shapes I in Technical Drawing. Explain assessed AO3, and
Subscribe to unlock allTeach me: Add a sectional view on a stated cutting plane, hatched at 45 degrees, and label it A-A
I am an SS2 student studying Orthographic Projection III in Technical Drawing. Explain add
Subscribe to unlock allTeach me: By shape a trowel, plumb bob, spirit level, mason's square, float, bolster and jointer
I am an SS2 student studying Building Tools and Freehand Sketching in Technical Drawing. E
Subscribe to unlock allPractice set: Sketching freehand, in pictorial view, four building tools in correct proportion within twenty
Set me five practice tasks on sketching freehand, in pictorial view, four building tools i
Subscribe to unlock allTeach me: Semicircular, segmental, flat or camber, pointed and relieving arches
I am an SS2 student studying Openings II: Arches and Lintels in Technical Drawing. Explain
Subscribe to unlock allProject task: Drawing the full detail to 1:10 on A3, annotate every layer
Set me a small project on drawing the full detail to 1:10 on A3, annotate every layer, the
Subscribe to unlock allWAEC prep: The difference between the eccentricity of a parabola and that of a hyperbola
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allTeach me: Constructing an epicycloid and a hypocycloid on a stated directing circle
You are my personal SS2 Technical Drawing tutor. Teach me constructing an epicycloid and a
Subscribe to unlock allSpot my mistake: Clockwise and anticlockwise motion and rotary from oscillating
Write a short SS2 Technical Drawing answer about clockwise and anticlockwise motion and ro
Subscribe to unlock allLet me explain: Graphic Products candidates meet the same content when drawing moving parts
I am going to explain graphic Products candidates meet the same content when drawing movin
Subscribe to unlock allProject task: Drawing the plan and elevation of a 60 mm diameter
Give me a practical task on drawing the plan and elevation of a 60 mm diameter from True S
Subscribe to unlock allPractice set: The four conic sections and the cutting plane that produces each
Set me five practice tasks on the four conic sections and the cutting plane that produces
Subscribe to unlock allQuiz: Assessed AO3 designing and communicating and AO4 evaluation
I am revising Development and Card Models for SS2 Technical Drawing. Test me on assessed A
Subscribe to unlock allWAEC prep: Develop and build in card a truncated cylinder of 50 mm diameter cut at 45 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock all