Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Showing the steps of an offset cutting plane as lines in the sectional view"
Teach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allPractice set: Enlarge and reduce plane figures based on the ratio of areas and verify the result
Set me five practice tasks on enlarge and reduce plane figures based on the ratio of areas
Subscribe to unlock allQuiz: 2. State the principles of converting the shape of a plane figure into another of equal area
Set me a quick recall test on 2. State the principles of converting the shape of a plane f
Subscribe to unlock allPractice set: Demonstrating and carry out the construction of plane figures of equal area
Set me five practice tasks on demonstrating and carry out the construction of plane figure
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allTeach me: 1. Define technical drawing in your own words and distinguish the two classifications of drawing
You are my personal SS1 Technical Drawing tutor. Teach me 1. Define technical drawing in y
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allTeach me: 1. Identify the types of lines used in technical drawing and the purpose and weight of each
You are my personal SS1 Technical Drawing tutor. Teach me 1. Identify the types of lines u
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allTeach me: 2. Plot the locus of a point on a rotating and a sliding mechanism
Be my SS1 Technical Drawing teacher for this one point: 2. Plot the locus of a point on a
Subscribe to unlock allTeach me: 1. Prepare the pattern development of a prism and of a cylinder
Be my SS1 Technical Drawing teacher for this one point: 1. Prepare the pattern development
Subscribe to unlock allTeach me: 1. Identify the types of pictorial drawing: isometric, oblique and perspective
Be my SS1 Technical Drawing teacher for this one point: 1. Identify the types of pictorial
Subscribe to unlock allTeach me: 2. Demonstrate the types of oblique drawing: cavalier and cabinet
Be my SS1 Technical Drawing teacher for this one point: 2. Demonstrate the types of obliqu
Subscribe to unlock allLet me explain: 3. State the advantages of CADD over manual drawing
Let me talk you through 3. State the advantages of CADD over manual drawing from the Drawi
Subscribe to unlock allQuiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock allLet me explain: 1. State the purpose of drawing standards
Let me talk you through 1. State the purpose of drawing standards from the Drawing Standar
Subscribe to unlock all