Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →181 prompts matching "Reading a floor plan as a view from above rather than as a horizontal section th"
Project task: Three views of a stepped block from a physical model
Set me a small project on three views of a stepped block from a physical model, the kind I
Subscribe to unlock allProject task: Building a composite object in isometric from three orthographic views
Give me a practical task on building a composite object in isometric from three orthograph
Subscribe to unlock allSpot my mistake: 4. Produce a finished isometric drawing of a composite object from orthographic views
Give me a wrong or muddled explanation of 4. Produce a finished isometric drawing of a com
Subscribe to unlock allPractice set: Producing a composite isometric drawing from orthographic views
Set me five practice tasks on producing a composite isometric drawing from orthographic vi
Subscribe to unlock allPractice set: Accuracy of construction assessed separately from knowledge
Set me five practice tasks on accuracy of construction assessed separately from knowledge,
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allPractice set: Enlarge and reduce plane figures based on the ratio of areas and verify the result
Set me five practice tasks on enlarge and reduce plane figures based on the ratio of areas
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock allQuiz: 2. Construct isometric circles as four-centre ellipses in all three isometric planes
I am revising Isometric Drawing II for SS1 Technical Drawing. Test me on 2. Construct isom
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allSpot my mistake: Formal assessment of the first term programme of study
Give me a wrong or muddled explanation of formal assessment of the first term programme of
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allTeach me: 1. Explain orthographic projection and distinguish first-angle from third-angle projection
You are my personal SS1 Technical Drawing tutor. Teach me 1. Explain orthographic projecti
Subscribe to unlock allTeach me: 1. Define technical drawing in your own words and distinguish the two classifications of drawing
You are my personal SS1 Technical Drawing tutor. Teach me 1. Define technical drawing in y
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock all