Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →283 prompts matching "Non-isometric lines and how they are plotted"
WAEC prep: Why hatching lines on a section are drawn at 45 degrees and spaced evenly
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allPractice set: Why layers, rather than a single drawing layer, are used for outline and hidden detail
Set me five practice tasks on why layers, rather than a single drawing layer, are used for
Subscribe to unlock allSpot my mistake: Drawing the lines of intersection of two square prisms meeting at 90 degrees
Show me a worked example on drawing the lines of intersection of two square prisms meeting
Subscribe to unlock allTeach me: How a second auxiliary view is used to obtain the true shape of a face inclined to both
You are my personal SS2 Technical Drawing tutor. Teach me how a second auxiliary view is u
Subscribe to unlock allSpot my mistake: Drawing the auxiliary elevation of a truncated square pyramid on a plane inclined at 50 degrees
Show me a worked example on drawing the auxiliary elevation of a truncated square pyramid
Subscribe to unlock allReal-life Nigeria: Are given a plan and elevation only and must state the position of each point in words
Show me how are given a plan and elevation only and must state the position of each point
Subscribe to unlock allQuiz: The parabola, hyperbola, involute and cycloid by the defining condition of each, compared
I am revising Loci and Special Curves for SS2 Technical Drawing. Test me on the parabola,
Subscribe to unlock allWAEC prep: Drawing the involute of a square of 30 mm side and measure the length of the final arc
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Why the cut face appears as a straight line in one view and an ellipse in another
Show me a worked example on why the cut face appears as a straight line in one view and an
Subscribe to unlock allLet me explain: Determine the true shape of the cut face of a square pyramid truncated by an inclined plane
I am going to explain determine the true shape of the cut face of a square pyramid truncat
Subscribe to unlock allTeach me: The true shape obtained with the shape shown in the plan, compared
Be my SS2 Technical Drawing teacher for this one point: the true shape obtained with the s
Subscribe to unlock allPractice set: Why the curve becomes two straight lines when the two cylinders are of equal diameter
Set me five practice tasks on why the curve becomes two straight lines when the two cylind
Subscribe to unlock allSpot my mistake: Three uses of perspective drawing and distinguish it from isometric and oblique drawing
Show me a worked example on three uses of perspective drawing and distinguish it from isom
Subscribe to unlock allTeach me: And locate the ground line, horizon, station point
You are my personal SS2 Technical Drawing tutor. Teach me and locate the ground line, hori
Subscribe to unlock allSpot my mistake: Four line types used in orthographic drawing and the purpose of each
Show me a worked example on four line types used in orthographic drawing and the purpose o
Subscribe to unlock allProject task: Enclosing box on the board and removes material step by step so the class sees the isometric
Give me a practical task on enclosing box on the board and removes material step by step s
Subscribe to unlock allSpot my mistake: Drawing the auxiliary views of a full hexagonal prism and a square pyramid
Show me a worked example on drawing the auxiliary views of a full hexagonal prism and a sq
Subscribe to unlock allSpot my mistake: Drawing the second auxiliary elevation of a shaped block and label both new ground lines
Show me a worked example on drawing the second auxiliary elevation of a shaped block and l
Subscribe to unlock allProject task: LINE, OFFSET, TRIM and ELLIPSE commands on the projector
Give me a practical task on LINE, OFFSET, TRIM and ELLIPSE commands on the projector from
Subscribe to unlock allSpot my mistake: Producing and plot an isometric drawing of a given block at 1:1 on A3
Show me a worked example on producing and plot an isometric drawing of a given block at 1:
Subscribe to unlock all