Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →214 prompts matching "Locating the centre of gravity of a given lamina"
Spot my mistake: 4. Determine the linear ratio corresponding to a given ratio of areas
Show me a worked example on 4. Determine the linear ratio corresponding to a given ratio o
Subscribe to unlock allLet me explain: 3. Produce the front elevation, end elevation and plan of a given solid in first angle
Let me talk you through 3. Produce the front elevation, end elevation and plan of a given
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allPractice set: Constructing triangles from all three sets of given data
Set me five practice tasks on constructing triangles from all three sets of given data, at
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allLet me explain: 4. Convert a given irregular polygon into a triangle of equal area and verify by calculation
Act as my study partner. I will teach you 4. Convert a given irregular polygon into a tria
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allTeach me: 2. Construct an arc of given radius externally enclosing two circles
I am an SS1 student studying Tangents and Tangency II in Technical Drawing. Explain 2. Con
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allTeach me: 1. Define technical drawing in your own words and distinguish the two classifications of drawing
You are my personal SS1 Technical Drawing tutor. Teach me 1. Define technical drawing in y
Subscribe to unlock allLet me explain: 3. State the advantages of CADD over manual drawing
Let me talk you through 3. State the advantages of CADD over manual drawing from the Drawi
Subscribe to unlock allWAEC prep: The two classifications of drawing, compared
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 3. Describe the purpose of lettering
I am going to explain 3. Describe the purpose of lettering to you, as an SS1 Technical Dra
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allWAEC prep: Success: all letters within ±0.5 mm of the guide-line height with uniform stroke thickness
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allTeach me: 1. Identify the types of lines used in technical drawing and the purpose and weight of each
You are my personal SS1 Technical Drawing tutor. Teach me 1. Identify the types of lines u
Subscribe to unlock all