Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "LINE, OFFSET, TRIM and ELLIPSE commands on the projector"
Spot my mistake: 2. Identify standard line types and their applications as set out in the drawing standard
Write a short SS1 Technical Drawing answer about 2. Identify standard line types and their
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allQuiz: 2. Determine the true length of a line by rotation and by auxiliary projection
Set me a quick recall test on 2. Determine the true length of a line by rotation and by au
Subscribe to unlock allWAEC prep: Success: sheet completed with correct pencil grade for outline, construction and dimension lines
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Identify the types of lines used in technical drawing and the purpose and weight of each
You are my personal SS1 Technical Drawing tutor. Teach me 1. Identify the types of lines u
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: 4. Determine the linear ratio corresponding to a given ratio of areas
Show me a worked example on 4. Determine the linear ratio corresponding to a given ratio o
Subscribe to unlock allQuiz: 1. Define and distinguish the ellipse, cycloid, trochoid, involute and helix
I am revising Special Curves for SS1 Technical Drawing. Test me on 1. Define and distingui
Subscribe to unlock allWAEC prep: Constructing an ellipse by three methods and a cycloid
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 3. Differentiate between isometric and non-isometric lines
Act as my study partner. I will teach you 3. Differentiate between isometric and non-isome
Subscribe to unlock allPractice set: Four-centre ellipse inside an isometric rhombus. Students construct isometric circles in the
Give me a practice set on four-centre ellipse inside an isometric rhombus. Students constr
Subscribe to unlock allTeach me: 1. Define technical drawing in your own words and distinguish the two classifications of drawing
You are my personal SS1 Technical Drawing tutor. Teach me 1. Define technical drawing in y
Subscribe to unlock allSpot my mistake: Producing vertical and inclined lettering to consistent height
Show me a worked example on producing vertical and inclined lettering to consistent height
Subscribe to unlock allTeach me: 1. Demonstrate safe handling of the drawing board, T-square and compass
Be my SS1 Technical Drawing teacher for this one point: 1. Demonstrate safe handling of th
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock all