Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →224 prompts matching "Full, half and part sections"
Practice set: And names each item in a full drawing set
Give me a practice set on and names each item in a full drawing set for SS1 Technical Draw
Subscribe to unlock allSpot my mistake: 2. Draw a circle and label its parts correctly
Write a short SS1 Technical Drawing answer about 2. Draw a circle and label its parts corr
Subscribe to unlock allReal-life Nigeria: Drawing a large circle and label all named parts
Take drawing a large circle and label all named parts out of the textbook. Describe a real
Subscribe to unlock allPractice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock allLet me explain: 3. Determine true lengths of the edges of full and truncated solids
I am going to explain 3. Determine true lengths of the edges of full and truncated solids
Subscribe to unlock allWAEC prep: Success: sheet completed with correct pencil grade for outline, construction and dimension lines
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Producing a hazard-and-control chart
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Five standard abbreviations with meanings
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Achieve at least 60% on a full mock paper
Show me a worked example on achieve at least 60% on a full mock paper with an error somewh
Subscribe to unlock allLet me explain: 3. State the properties of regular polygons including interior, exterior and central angles
Act as my study partner. I will teach you 3. State the properties of regular polygons incl
Subscribe to unlock allLet me explain: 3. Describe the applications of enlargement and reduction in design and manufacture
Act as my study partner. I will teach you 3. Describe the applications of enlargement and
Subscribe to unlock allLet me explain: 4. Convert a given irregular polygon into a triangle of equal area and verify by calculation
Act as my study partner. I will teach you 4. Convert a given irregular polygon into a tria
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: all blends visually smooth with tangency points marked and radii within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 4. Relate loci to the motion produced by levers, linkages and rotary systems
Act as my study partner. I will teach you 4. Relate loci to the motion produced by levers,
Subscribe to unlock allWAEC prep: Constructing an ellipse by three methods and a cycloid
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all