Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Block with an inclined face against a card plane"
Spot my mistake: Success: four-centre ellipses drawn correctly in all three planes with smooth arc junctions
Show me a worked example on success: four-centre ellipses drawn correctly in all three pla
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allSpot my mistake: 4. Produce single-stroke vertical and inclined Gothic letters
Give me a wrong or muddled explanation of 4. Produce single-stroke vertical and inclined G
Subscribe to unlock allSpot my mistake: Producing vertical and inclined lettering to consistent height
Show me a worked example on producing vertical and inclined lettering to consistent height
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allQuiz: 2. Construct isometric circles as four-centre ellipses in all three isometric planes
I am revising Isometric Drawing II for SS1 Technical Drawing. Test me on 2. Construct isom
Subscribe to unlock allPractice set: Cavalier and cabinet oblique of the same block so students can see the halved receding depth.
Give me a practice set on cavalier and cabinet oblique of the same block so students can s
Subscribe to unlock allQuiz: 3. Use a graphics package to produce plane and pictorial figures
I am revising Introduction to Computer Graphics and Cad for SS1 Technical Drawing. Test me
Subscribe to unlock allWAEC prep: Success: sheet completed with correct pencil grade for outline, construction and dimension lines
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 2. Prepare a title block and border to standard proportions on a drawing sheet
Set me a quick recall test on 2. Prepare a title block and border to standard proportions
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allPractice set: Constructing the special angles without a protractor
Set me five practice tasks on constructing the special angles without a protractor, at the
Subscribe to unlock allSpot my mistake: Success: every constructed angle within ±1° when checked with a protractor
Show me a worked example on success: every constructed angle within ±1° when checked with
Subscribe to unlock allProject task: Constructing a specified triangle accurately within a time limit
Set me a small project on constructing a specified triangle accurately within a time limit
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all