Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →287 prompts matching "4. Calculate the interior and exterior angles of any regular polygon"
Teach me: Drawing the front elevation, plan and end elevation of a given shaped block in first angle
Be my SS2 Technical Drawing teacher for this one point: drawing the front elevation, plan
Subscribe to unlock allWAEC prep: The difference between first and third angle projection in terms of where the plan is placed
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allPractice set: Modelling-clay cone at four angles in front of the class
Give me a practice set on modelling-clay cone at four angles in front of the class for SS2
Subscribe to unlock allReal-life Nigeria: Checking each other's stroke measurement against the calculated value of twice the crank radius
Take checking each other's stroke measurement against the calculated value of twice the cr
Subscribe to unlock allPractice set: Vertical edges of both prisms and shows how each edge of the branch pierces two faces of the
Give me a practice set on vertical edges of both prisms and shows how each edge of the bra
Subscribe to unlock allSpot my mistake: Drawing the auxiliary elevation and auxiliary plan of a truncated hexagonal prism
Write a short SS2 Technical Drawing answer about drawing the auxiliary elevation and auxil
Subscribe to unlock allSpot my mistake: The meaning of the horizontal plane, the vertical plane and the reference line XY
Write a short SS2 Technical Drawing answer about the meaning of the horizontal plane, the
Subscribe to unlock allPractice set: Rod at an angle to both card planes and rotates it into a position parallel to the VP so the
Give me a practice set on rod at an angle to both card planes and rotates it into a positi
Subscribe to unlock allPractice set: Card triangle in the two-plane model and turns it until the class sees it edge-on
Give me a practice set on card triangle in the two-plane model and turns it until the clas
Subscribe to unlock allSpot my mistake: The angle of inclination of the lamina to the horizontal plane to the nearest degree
Show me a worked example on the angle of inclination of the lamina to the horizontal plane
Subscribe to unlock allQuiz: The parabola, hyperbola, involute and cycloid by the defining condition of each, compared
I am revising Loci and Special Curves for SS2 Technical Drawing. Test me on the parabola,
Subscribe to unlock allQuiz: Constructing a parabola by the focus and directrix method for an eccentricity of 1
Set me a quick recall test on constructing a parabola by the focus and directrix method fo
Subscribe to unlock allPractice set: Comparing the two curves and account for any difference
Give me a practice set on comparing the two curves and account for any difference for SS2
Subscribe to unlock allWAEC prep: The difference between the eccentricity of a parabola and that of a hyperbola
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allLet me explain: Constructing the involute of a square and of a regular hexagon of 30 mm side
Act as my study partner. I will teach you constructing the involute of a square and of a r
Subscribe to unlock allWAEC prep: Drawing the involute of a square of 30 mm side and measure the length of the final arc
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allLet me explain: The meaning of link, joint, crank, lever, slider and frame
Let me talk you through the meaning of link, joint, crank, lever, slider and frame from th
Subscribe to unlock allQuiz: Sketching freehand the mechanism of a pair of scissors
Set me a quick recall test on sketching freehand the mechanism of a pair of scissors at SS
Subscribe to unlock allQuiz: Drawing a slider-crank mechanism and plot the locus of the mid-point of the connecting rod
Quiz me on drawing a slider-crank mechanism and plot the locus of the mid-point of the con
Subscribe to unlock allProject task: Drawing the plan and elevation of a 60 mm diameter
Give me a practical task on drawing the plan and elevation of a 60 mm diameter from True S
Subscribe to unlock all