Technical Drawing

AI prompts for senior secondary learners.

📅 36-Week WAEC Study Guide for Technical Drawing →

Three prompts in each subject are free to try. One subscription opens every subject and every prompt in senior secondary, or subscribe your whole school. Already have a code? Enter it here.

Show:All prompts Free

Year group:All years SS 1 SS 2 SS 3

Year 12 key words:angles and triangles bisecting and dividing building drawing circles and tangents conic sections drawing instruments forces and structures isometric drawing lines and lettering orthographic projection polygons scales

+ 2 more key words

screw threads and fasteners sectional views

153 prompts matching "Quiz: Sketching freehand pictorial views of four selected tools in correct propo"

Spot my mistake: Developing the curved surface of a cone as a rectangle of the same height

PPJ-TDR-00514 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on developing the curved surfa

Subscribe to unlock all

Spot my mistake: Assuming the intersection of two equal cylinders meeting at right angles is always a curve

PPJ-TDR-00515 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming the intersection o

Subscribe to unlock all

Spot my mistake: Treating the resultant and the equilibrant of a force system as the same force

PPJ-TDR-00516 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on treating the resultant and

Subscribe to unlock all

Spot my mistake: Reading a floor plan as a view from above rather than as a horizontal section through the building

PPJ-TDR-00519 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on reading a floor plan as a v

Subscribe to unlock all

Spot my mistake: Treating a tolerance as the error the workshop is expected to make rather than the permitted range of size

PPJ-TDR-00520 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on treating a tolerance as the

Subscribe to unlock all

Spot my mistake: Placing the damp proof membrane beneath the hardcore in a solid floor

PPJ-TDR-00525 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on placing the damp proof memb

Subscribe to unlock all

Spot my mistake: Treating the going and the tread of a stair as the same dimension

PPJ-TDR-00527 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on treating the going and the

Subscribe to unlock all

Spot my mistake: Assuming a flat roof is laid truly level

PPJ-TDR-00528 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a flat roof is lai

Subscribe to unlock all

Spot my mistake: Reading the line joining two electrical symbols on a plan as the actual route of the cable

PPJ-TDR-00530 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on reading the line joining tw

Subscribe to unlock all

Spot my mistake: Drawing the true helix of a screw thread rather than its conventional representation

PPJ-TDR-00533 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on drawing the true helix of a

Subscribe to unlock all

Spot my mistake: Assuming a line inclined in both views can have its true length measured in either

PPJ-TDR-00541 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a line inclined in

Subscribe to unlock all

Spot my mistake: Measuring the angle between two planes in a view where neither appears as an edge

PPJ-TDR-00542 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on measuring the angle between

Subscribe to unlock all

Spot my mistake: Assuming the centre of gravity of a lamina must lie within its outline

PPJ-TDR-00544 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming the centre of grav

Subscribe to unlock all