Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →215 prompts matching "Quiz: Finding the centre of a given arc"
Spot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allSpot my mistake: 4. Identify the constructions used to transfer area between shapes
Give me a wrong or muddled explanation of 4. Identify the constructions used to transfer a
Subscribe to unlock allPractice set: Success: radius and tangent perpendicular within ±1° at every point of tangency
Set me five practice tasks on success: radius and tangent perpendicular within ±1° at ever
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allProject task: Three views of a stepped block from a physical model
Set me a small project on three views of a stepped block from a physical model, the kind I
Subscribe to unlock allSpot my mistake: 4. Distinguish chain, parallel and running dimensioning and select the appropriate system
Give me a wrong or muddled explanation of 4. Distinguish chain, parallel and running dimen
Subscribe to unlock allReal-life Nigeria: Dimensioning rules with examples of correct
Take dimensioning rules with examples of correct out of the textbook. Describe a real Nige
Subscribe to unlock allPractice set: Constructing isometric squares, rectangles, arcs and circles
Set me five practice tasks on constructing isometric squares, rectangles, arcs and circles
Subscribe to unlock allSpot my mistake: 4. Produce a finished isometric drawing of a composite object from orthographic views
Give me a wrong or muddled explanation of 4. Produce a finished isometric drawing of a com
Subscribe to unlock allQuiz: 2. Distinguish between drawing materials and drawing instruments
I am revising Drawing Materials and Equipment for SS1 Technical Drawing. Test me on 2. Dis
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allPractice set: Constructing the special angles without a protractor
Set me five practice tasks on constructing the special angles without a protractor, at the
Subscribe to unlock allSpot my mistake: Constructing an inscribed, a circumscribed and an escribed circle for a given triangle
Show me a worked example on constructing an inscribed, a circumscribed and an escribed cir
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 4. Construct any quadrilateral when four sides and one diagonal are known
I am revising Quadrilaterals for SS1 Technical Drawing. Test me on 4. Construct any quadri
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allSpot my mistake: 2. Identify standard line types and their applications as set out in the drawing standard
Write a short SS1 Technical Drawing answer about 2. Identify standard line types and their
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock all