Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Convert given orthographic views into an isometric view drawn to full size"
Quiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allPractice set: Constructing the special angles without a protractor
Set me five practice tasks on constructing the special angles without a protractor, at the
Subscribe to unlock allSpot my mistake: Success: every constructed angle within ±1° when checked with a protractor
Show me a worked example on success: every constructed angle within ±1° when checked with
Subscribe to unlock allTeach me: 1. Define a triangle
Be my SS1 Technical Drawing teacher for this one point: 1. Define a triangle. Start with w
Subscribe to unlock allQuiz: 2. Classify triangles by sides
Quiz me on 2. Classify triangles by sides, from the SS1 Technical Drawing topic Angles and
Subscribe to unlock allProject task: Constructing a specified triangle accurately within a time limit
Set me a small project on constructing a specified triangle accurately within a time limit
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock allSpot my mistake: 2. Draw a circle and label its parts correctly
Write a short SS1 Technical Drawing answer about 2. Draw a circle and label its parts corr
Subscribe to unlock allTeach me: 3. Distinguish eccentric from concentric circles and illustrate each
I am an SS1 student studying Circles and Triangles I in Technical Drawing. Explain 3. Dist
Subscribe to unlock allReal-life Nigeria: Drawing a large circle and label all named parts
Take drawing a large circle and label all named parts out of the textbook. Describe a real
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock allPractice set: Incentre construction using angle bisectors
Give me a practice set on incentre construction using angle bisectors for SS1 Technical Dr
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 4. Construct any quadrilateral when four sides and one diagonal are known
I am revising Quadrilaterals for SS1 Technical Drawing. Test me on 4. Construct any quadri
Subscribe to unlock allSpot my mistake: Constructing special quadrilaterals and one from four sides and a diagonal
Show me a worked example on constructing special quadrilaterals and one from four sides an
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all