Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →287 prompts matching "Treating an isometric drawing as a perspective view with lines converging on a v"
Real-life Nigeria: Drawing auxiliary views of a 50 mm diameter cylinder
Show me how drawing auxiliary views of a 50 mm diameter cylinder works in real life in Nig
Subscribe to unlock allWAEC prep: Drawing the auxiliary plan of a 60 mm high cone on a plane inclined at 45 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allLet me explain: Assessed AO3, and truncated solids in auxiliary projection are frequent in WAEC and NECO Paper 2
I am going to explain assessed AO3, and truncated solids in auxiliary projection are frequ
Subscribe to unlock allWAEC prep: Measuring and state the major and minor axes of the true shape obtained, in millimetres
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allProject task: LINE, OFFSET, TRIM and ELLIPSE commands on the projector
Give me a practical task on LINE, OFFSET, TRIM and ELLIPSE commands on the projector from
Subscribe to unlock allPractice set: Rotating the UCS and setting up a viewport so the auxiliary direction becomes horizontal on
Give me a practice set on rotating the UCS and setting up a viewport so the auxiliary dire
Subscribe to unlock allReal-life Nigeria: Comparing the CAD auxiliary with their Week 8 board drawing
Take comparing the CAD auxiliary with their Week 8 board drawing out of the textbook. Desc
Subscribe to unlock allProject task: Plotting six points at given distances above the HP
Give me a practical task on plotting six points at given distances above the HP from Trace
Subscribe to unlock allPractice set: Card triangle in the two-plane model and turns it until the class sees it edge-on
Give me a practice set on card triangle in the two-plane model and turns it until the clas
Subscribe to unlock allLet me explain: Sketching freehand front, top and side views of two of the same tools
I am going to explain sketching freehand front, top and side views of two of the same tool
Subscribe to unlock allProject task: Parts on a real door and window in the classroom, then repeats them on a chart
Give me a practical task on parts on a real door and window in the classroom, then repeats
Subscribe to unlock allWAEC prep: Why an arch is built with an odd number of voussoirs and a keystone at the crown
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allPractice set: Real stair in the school with the class
Give me a practice set on real stair in the school with the class for SS2 Technical Drawin
Subscribe to unlock allTeach me: Drawing the plan of a hipped roof showing hips, valleys and the run of the common rafters
Be my SS2 Technical Drawing teacher for this one point: drawing the plan of a hipped roof
Subscribe to unlock allPractice set: Describe, with an annotated sketch, one product whose form follows a parabola
Set me five practice tasks on describe, with an annotated sketch, one product whose form f
Subscribe to unlock allLet me explain: Graphic Products candidates meet the same content when drawing moving parts
I am going to explain graphic Products candidates meet the same content when drawing movin
Subscribe to unlock allSpot my mistake: Drawing a four-bar linkage to given link lengths and set out twelve crank positions
Give me a wrong or muddled explanation of drawing a four-bar linkage to given link lengths
Subscribe to unlock allQuiz: Drawing a slider-crank mechanism and plot the locus of the mid-point of the connecting rod
Quiz me on drawing a slider-crank mechanism and plot the locus of the mid-point of the con
Subscribe to unlock allReal-life Nigeria: Checking each other's stroke measurement against the calculated value of twice the crank radius
Take checking each other's stroke measurement against the calculated value of twice the cr
Subscribe to unlock allTeach me: Assessed AO3, and true shapes of truncated solids are a standing WAEC and NECO question
I am an SS2 student studying True Shapes I in Technical Drawing. Explain assessed AO3, and
Subscribe to unlock all