Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →212 prompts matching "Display the finished models beside the drawings"
Quiz: 4. Explain the geometric basis of each construction using bisectors
Quiz me on 4. Explain the geometric basis of each construction using bisectors, from the S
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 3. Construct the special quadrilaterals to given dimensions
You are my personal SS1 Technical Drawing tutor. Teach me 3. Construct the special quadril
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock allTeach me: 1. Construct a regular polygon using the square (general) method
You are my personal SS1 Technical Drawing tutor. Teach me 1. Construct a regular polygon u
Subscribe to unlock allQuiz: 2. Construct a regular polygon using the circle (circumscribing) method
I am revising Polygons II for SS1 Technical Drawing. Test me on 2. Construct a regular pol
Subscribe to unlock allLet me explain: 3. Construct a regular polygon using the diagonal method
Let me talk you through 3. Construct a regular polygon using the diagonal method from the
Subscribe to unlock allSpot my mistake: 4. Compare the three methods for accuracy
Write a short SS1 Technical Drawing answer about 4. Compare the three methods for accuracy
Subscribe to unlock allPractice set: Each of the three methods for a regular heptagon. Students construct a heptagon by all three
Give me a practice set on each of the three methods for a regular heptagon. Students const
Subscribe to unlock allWAEC prep: Success: sides of the heptagon equal within 0.5 mm by at least two of the three methods
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allLet me explain: 3. Apply the radial (ray) method of enlargement from a chosen pole
Let me talk you through 3. Apply the radial (ray) method of enlargement from a chosen pole
Subscribe to unlock allSpot my mistake: 4. Verify the accuracy of an enlargement by measurement and calculation
Write a short SS1 Technical Drawing answer about 4. Verify the accuracy of an enlargement
Subscribe to unlock allReal-life Nigeria: Enlarge an irregular pentagon in the ratio of areas 3:2
Show me how enlarge an irregular pentagon in the ratio of areas 3:2 works in real life in
Subscribe to unlock allTeach me: 1. Outline the principles of determining figures of equal area
I am an SS1 student studying Equal Areas of Similar Figures I in Technical Drawing. Explai
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allPractice set: Completing the four standard equal-area constructions on one sheet
Give me a practice set on completing the four standard equal-area constructions on one she
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock allTeach me: 2. Plot the locus of a point on a rotating and a sliding mechanism
Be my SS1 Technical Drawing teacher for this one point: 2. Plot the locus of a point on a
Subscribe to unlock all