Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Constructing a hyperbola from given foci and a constant difference of 30 mm"
Teach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allPractice set: Accuracy of construction assessed separately from knowledge
Set me five practice tasks on accuracy of construction assessed separately from knowledge,
Subscribe to unlock allQuiz: 2. Distinguish regular from irregular polygons
Quiz me on 2. Distinguish regular from irregular polygons, from the SS1 Technical Drawing
Subscribe to unlock allReal-life Nigeria: Naming polygons from three to twelve sides
Take naming polygons from three to twelve sides out of the textbook. Describe a real Niger
Subscribe to unlock allLet me explain: 3. Construct a plain scale to a given representative fraction
I am going to explain 3. Construct a plain scale to a given representative fraction to you
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allPractice set: Success: five dimensions set off from the diagonal scale correct within 0.5 mm
Set me five practice tasks on success: five dimensions set off from the diagonal scale cor
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allQuiz: 2. Distinguish between enlargement by ratio of sides and by ratio of areas
Quiz me on 2. Distinguish between enlargement by ratio of sides and by ratio of areas, fro
Subscribe to unlock allSpot my mistake: 4. Determine the linear ratio corresponding to a given ratio of areas
Show me a worked example on 4. Determine the linear ratio corresponding to a given ratio o
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allLet me explain: 3. Apply the radial (ray) method of enlargement from a chosen pole
Let me talk you through 3. Apply the radial (ray) method of enlargement from a chosen pole
Subscribe to unlock allLet me explain: 4. Construct common tangents to two equal and to two unequal circles
Let me talk you through 4. Construct common tangents to two equal and to two unequal circl
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allTeach me: 2. Plot the locus of a point on a rotating and a sliding mechanism
Be my SS1 Technical Drawing teacher for this one point: 2. Plot the locus of a point on a
Subscribe to unlock allQuiz: 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism
Quiz me on 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism, fr
Subscribe to unlock allPractice set: Plotting the loci of a point at a fixed distance from a line
Give me a practice set on plotting the loci of a point at a fixed distance from a line for
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allSpot my mistake: 4. Prepare the pattern development of a pyramid and of a cone
Give me a wrong or muddled explanation of 4. Prepare the pattern development of a pyramid
Subscribe to unlock all