Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →224 prompts matching "Practising crating and proportion exercises"
Spot my mistake: And produce all six line types at correct weight
Show me a worked example on and produce all six line types at correct weight with an error
Subscribe to unlock allQuiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allSpot my mistake: Given two sides and the included angle
Show me a worked example on given two sides and the included angle with an error somewhere
Subscribe to unlock allTeach me: Given one side and two angles
You are my personal SS1 Technical Drawing tutor. Teach me given one side and two angles, a
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock allSpot my mistake: 2. Draw a circle and label its parts correctly
Write a short SS1 Technical Drawing answer about 2. Draw a circle and label its parts corr
Subscribe to unlock allTeach me: 3. Distinguish eccentric from concentric circles and illustrate each
I am an SS1 student studying Circles and Triangles I in Technical Drawing. Explain 3. Dist
Subscribe to unlock allQuiz: 4. Construct eccentric and concentric circles to given dimensions
Set me a quick recall test on 4. Construct eccentric and concentric circles to given dimen
Subscribe to unlock allReal-life Nigeria: Drawing a large circle and label all named parts
Take drawing a large circle and label all named parts out of the textbook. Describe a real
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock allTeach me: 3. Describe an escribed circle and construct one to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 3. Describe an escribed circle and
Subscribe to unlock allSpot my mistake: Constructing an inscribed, a circumscribed and an escribed circle for a given triangle
Show me a worked example on constructing an inscribed, a circumscribed and an escribed cir
Subscribe to unlock allQuiz: 4. Construct any quadrilateral when four sides and one diagonal are known
I am revising Quadrilaterals for SS1 Technical Drawing. Test me on 4. Construct any quadri
Subscribe to unlock allSpot my mistake: Constructing special quadrilaterals and one from four sides and a diagonal
Show me a worked example on constructing special quadrilaterals and one from four sides an
Subscribe to unlock allLet me explain: 1. State the purpose of drawing standards
Let me talk you through 1. State the purpose of drawing standards from the Drawing Standar
Subscribe to unlock all