Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →204 prompts matching "Isometric drawing of a machine part"
WAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: sides of the heptagon equal within 0.5 mm by at least two of the three methods
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 3. Construct isometric arcs and fillets
Let me talk you through 3. Construct isometric arcs and fillets from the Isometric Drawing
Subscribe to unlock allPractice set: Two advantages of CADD
Set me five practice tasks on two advantages of CADD, at the level expected in SS1 Drawing
Subscribe to unlock allQuiz: 2. Prepare a title block and border to standard proportions on a drawing sheet
Set me a quick recall test on 2. Prepare a title block and border to standard proportions
Subscribe to unlock allLet me explain: 3. Describe the purpose of lettering
I am going to explain 3. Describe the purpose of lettering to you, as an SS1 Technical Dra
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allPractice set: Demonstrating safe handling of board, T-square and compass
Set me five practice tasks on demonstrating safe handling of board, T-square and compass,
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allSpot my mistake: 2. Draw a circle and label its parts correctly
Write a short SS1 Technical Drawing answer about 2. Draw a circle and label its parts corr
Subscribe to unlock allQuiz: 4. Explain the geometric basis of each construction using bisectors
Quiz me on 4. Explain the geometric basis of each construction using bisectors, from the S
Subscribe to unlock allLet me explain: 3. State the properties of regular polygons including interior, exterior and central angles
Act as my study partner. I will teach you 3. State the properties of regular polygons incl
Subscribe to unlock allPractice set: Each of the three methods for a regular heptagon. Students construct a heptagon by all three
Give me a practice set on each of the three methods for a regular heptagon. Students const
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allQuiz: 2. Distinguish between enlargement by ratio of sides and by ratio of areas
Quiz me on 2. Distinguish between enlargement by ratio of sides and by ratio of areas, fro
Subscribe to unlock allLet me explain: 3. Describe the applications of enlargement and reduction in design and manufacture
Act as my study partner. I will teach you 3. Describe the applications of enlargement and
Subscribe to unlock allProject task: Why doubling the area of a square requires a side ratio of √2
Give me a practical task on why doubling the area of a square requires a side ratio of √2
Subscribe to unlock all