Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Drawing an isometric circle of 40 mm diameter by the four-centre method"
Practice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock allLet me explain: 1. State the purpose of drawing standards
Let me talk you through 1. State the purpose of drawing standards from the Drawing Standar
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allQuiz: 2. Define isometric drawing and the isometric axes at 30° to the horizontal
Quiz me on 2. Define isometric drawing and the isometric axes at 30° to the horizontal, fr
Subscribe to unlock allWAEC prep: Perspective and shading in isometric drawing
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 2. Demonstrate the types of oblique drawing: cavalier and cabinet
Be my SS1 Technical Drawing teacher for this one point: 2. Demonstrate the types of obliqu
Subscribe to unlock allWAEC prep: Success: all letters within ±0.5 mm of the guide-line height with uniform stroke thickness
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: sides of the heptagon equal within 0.5 mm by at least two of the three methods
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: Formal assessment of the second term programme of study
You are my personal SS1 Technical Drawing tutor. Teach me formal assessment of the second
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allLet me explain: 3. Construct isometric arcs and fillets
Let me talk you through 3. Construct isometric arcs and fillets from the Isometric Drawing
Subscribe to unlock allTeach me: Formal end-of-year assessment covering the whole Year 10 programme of study
I am an SS1 student studying Examination in Technical Drawing. Explain formal end-of-year
Subscribe to unlock allWAEC prep: The two classifications of drawing, compared
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Two advantages of CADD
Set me five practice tasks on two advantages of CADD, at the level expected in SS1 Drawing
Subscribe to unlock allQuiz: 2. Prepare a title block and border to standard proportions on a drawing sheet
Set me a quick recall test on 2. Prepare a title block and border to standard proportions
Subscribe to unlock allPractice set: Demonstrating safe handling of board, T-square and compass
Set me five practice tasks on demonstrating safe handling of board, T-square and compass,
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allPractice set: Each construction step by step on the board. Students construct the full set of special angles
Give me a practice set on each construction step by step on the board. Students construct
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: 2. Draw a circle and label its parts correctly
Write a short SS1 Technical Drawing answer about 2. Draw a circle and label its parts corr
Subscribe to unlock all