Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Drawing a tangent that meets the radius at the point of contact at any convenien"
Practice set: Success: assessed observation checklist passed on all five safety points
Set me five practice tasks on success: assessed observation checklist passed on all five s
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock allProject task: Why doubling the area of a square requires a side ratio of √2
Give me a practical task on why doubling the area of a square requires a side ratio of √2
Subscribe to unlock allSpot my mistake: 4. Verify the accuracy of an enlargement by measurement and calculation
Write a short SS1 Technical Drawing answer about 4. Verify the accuracy of an enlargement
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism
Quiz me on 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism, fr
Subscribe to unlock allLet me explain: 3. Determine true lengths of the edges of full and truncated solids
I am going to explain 3. Determine true lengths of the edges of full and truncated solids
Subscribe to unlock allTeach me: 1. Prepare the pattern development of a prism and of a cylinder
Be my SS1 Technical Drawing teacher for this one point: 1. Prepare the pattern development
Subscribe to unlock allLet me explain: 3. Produce the front elevation, end elevation and plan of a given solid in first angle
Let me talk you through 3. Produce the front elevation, end elevation and plan of a given
Subscribe to unlock allSpot my mistake: 4. Interpret a three-view orthographic drawing and sketch the solid it represents
Write a short SS1 Technical Drawing answer about 4. Interpret a three-view orthographic dr
Subscribe to unlock allTeach me: 1. Identify the types of pictorial drawing: isometric, oblique and perspective
Be my SS1 Technical Drawing teacher for this one point: 1. Identify the types of pictorial
Subscribe to unlock allTeach me: 1. Arrange an appropriate working area before starting a drawing
I am an SS1 student studying Board Practice: Title Block and Lettering in Technical Drawin
Subscribe to unlock allQuiz: 2. Identify hazards in the drawing studio
Quiz me on 2. Identify hazards in the drawing studio, from the SS1 Technical Drawing topic
Subscribe to unlock allTeach me: 1. Identify the types of lines used in technical drawing and the purpose and weight of each
You are my personal SS1 Technical Drawing tutor. Teach me 1. Identify the types of lines u
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock all