Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →282 prompts matching "Annotating a joint with the correct weld symbol"
Teach me: The term locus
You are my personal SS2 Technical Drawing tutor. Teach me the term locus, as it is taught
Subscribe to unlock allQuiz: The parabola, hyperbola, involute and cycloid by the defining condition of each, compared
I am revising Loci and Special Curves for SS2 Technical Drawing. Test me on the parabola,
Subscribe to unlock allLet me explain: Constructing a parabola inside a given rectangle 100 mm by 60 mm by the intersecting-lines
I am going to explain constructing a parabola inside a given rectangle 100 mm by 60 mm by
Subscribe to unlock allTeach me: Drawing the tangent and normal at a stated point on each curve
Be my SS2 Technical Drawing teacher for this one point: drawing the tangent and normal at
Subscribe to unlock allPractice set: Comparing the two curves and account for any difference
Give me a practice set on comparing the two curves and account for any difference for SS2
Subscribe to unlock allWAEC prep: The difference between the eccentricity of a parabola and that of a hyperbola
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allPractice set: Describe, with an annotated sketch, one product whose form follows a parabola
Set me five practice tasks on describe, with an annotated sketch, one product whose form f
Subscribe to unlock allPractice set: Lay a plastic gear or bicycle sprocket over their finished involute
Give me a practice set on lay a plastic gear or bicycle sprocket over their finished invol
Subscribe to unlock allWAEC prep: Drawing the involute of a square of 30 mm side and measure the length of the final arc
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allLet me explain: Graphic Products candidates meet the same content when drawing moving parts
I am going to explain graphic Products candidates meet the same content when drawing movin
Subscribe to unlock allSpot my mistake: The motion at the needle of a treadle sewing machine when the treadle oscillates
Show me a worked example on the motion at the needle of a treadle sewing machine when the
Subscribe to unlock allTeach me: Plotting the locus of a stated point on the coupler of the four-bar chain
Be my SS2 Technical Drawing teacher for this one point: plotting the locus of a stated poi
Subscribe to unlock allSpot my mistake: Here the locus plot supplies the evidence
Show me a worked example on here the locus plot supplies the evidence with an error somewh
Subscribe to unlock allWAEC prep: Plotting the locus of the mid-point of the connecting rod for twelve crank positions
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: What happens to the output at a dead-centre position
Show me a worked example on what happens to the output at a dead-centre position with an e
Subscribe to unlock allTeach me: What is meant by the true shape of a cut surface
You are my personal SS2 Technical Drawing tutor. Teach me what is meant by the true shape
Subscribe to unlock allQuiz: Determine the true shape of a right cone truncated at 45 degrees to the axis
I am revising True Shapes I for SS2 Technical Drawing. Test me on determine the true shape
Subscribe to unlock allPractice set: Modelling-clay cone at four angles in front of the class
Give me a practice set on modelling-clay cone at four angles in front of the class for SS2
Subscribe to unlock allProject task: Drawing the plan and elevation of a 60 mm diameter
Give me a practical task on drawing the plan and elevation of a 60 mm diameter from True S
Subscribe to unlock allWAEC prep: Determine the true shape of the cut face of a 50 mm diameter cylinder truncated at 30 degrees
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock all