Technical Drawing

AI prompts for senior secondary learners.

📅 36-Week WAEC Study Guide for Technical Drawing →

Three prompts in each subject are free to try. One subscription opens every subject and every prompt in senior secondary, or subscribe your whole school. Already have a code? Enter it here.

Show:All prompts Free

Year group:All years SS 1 SS 2 SS 3

Year 12 key words:angles and triangles bisecting and dividing building drawing circles and tangents conic sections drawing instruments forces and structures isometric drawing lines and lettering orthographic projection polygons scales

+ 2 more key words

screw threads and fasteners sectional views

296 prompts matching "Producing an isometric drawing of a shaped block"

Spot my mistake: Assuming a raft foundation is chosen where the ground is strongest

PPJ-TDR-00524 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a raft foundation

Subscribe to unlock all

Spot my mistake: Assuming every wall in a building carries load

PPJ-TDR-00529 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming every wall in a bu

Subscribe to unlock all

Spot my mistake: Reading a weld symbol below the reference line as though it sat above it

PPJ-TDR-00531 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on reading a weld symbol below

Subscribe to unlock all

Spot my mistake: Assuming a plain washer locks a nut against loosening

PPJ-TDR-00534 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a plain washer loc

Subscribe to unlock all

Spot my mistake: Sectioning a shaft, a bolt or a rib along its length

PPJ-TDR-00535 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on sectioning a shaft, a bolt

Subscribe to unlock all

Let me explain: Dividing a line in a given ratio

PPJ-TDR-00025 Similar prompts

I have just studied dividing a line in a given ratio in my SS3 Technical Drawing class. Le

Subscribe to unlock all

Let me explain: Constructing a regular polygon on a given side

PPJ-TDR-00055 Similar prompts

I have just studied constructing a regular polygon on a given side in my SS3 Technical Dra

Subscribe to unlock all

Let me explain: Constructing a circle through three given points

PPJ-TDR-00065 Similar prompts

I have just studied constructing a circle through three given points in my SS3 Technical D

Subscribe to unlock all

Let me explain: Enlarging or reducing a figure by area

PPJ-TDR-00095 Similar prompts

I have just studied enlarging or reducing a figure by area in my SS3 Technical Drawing cla

Subscribe to unlock all

Let me explain: One-point perspective

PPJ-TDR-00125 Similar prompts

I have just studied one-point perspective in my SS3 Technical Drawing class. Let me explai

Subscribe to unlock all

Let me explain: The second auxiliary projection

PPJ-TDR-00145 Similar prompts

I have just studied the second auxiliary projection in my SS3 Technical Drawing class. Let

Subscribe to unlock all

Let me explain: Sketching a building tool in pictorial view

PPJ-TDR-00254 Similar prompts

I have just studied sketching a building tool in pictorial view in my SS3 Technical Drawin

Subscribe to unlock all

Let me explain: The part or local section

PPJ-TDR-00394 Similar prompts

I have just studied the part or local section in my SS3 Technical Drawing class. Let me ex

Subscribe to unlock all

Let me explain: Setting up a two-point perspective

PPJ-TDR-00434 Similar prompts

I have just studied setting up a two-point perspective in my SS3 Technical Drawing class.

Subscribe to unlock all

Let me explain: Projecting a third view from two given views

PPJ-TDR-00444 Similar prompts

I have just studied projecting a third view from two given views in my SS3 Technical Drawi

Subscribe to unlock all

Let me explain: Finding true length by auxiliary projection

PPJ-TDR-00464 Similar prompts

I have just studied finding true length by auxiliary projection in my SS3 Technical Drawin

Subscribe to unlock all