Technical Drawing

AI prompts for senior secondary learners.

📅 36-Week WAEC Study Guide for Technical Drawing →

Three prompts in each subject are free to try. One subscription opens every subject and every prompt in senior secondary, or subscribe your whole school. Already have a code? Enter it here.

Show:All prompts Free

Year group:All years SS 1 SS 2 SS 3

Year 12 key words:angles and triangles bisecting and dividing building drawing circles and tangents conic sections drawing instruments forces and structures isometric drawing lines and lettering orthographic projection polygons scales

+ 2 more key words

screw threads and fasteners sectional views

296 prompts matching "Constructing an epicycloid and a hypocycloid on a stated directing circle"

Spot my mistake: Sketching a tool in orthographic views where a pictorial view is asked for

PPJ-TDR-00522 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on sketching a tool in orthogr

Subscribe to unlock all

Spot my mistake: Assuming a flat roof is laid truly level

PPJ-TDR-00528 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a flat roof is lai

Subscribe to unlock all

Spot my mistake: Assuming every wall in a building carries load

PPJ-TDR-00529 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming every wall in a bu

Subscribe to unlock all

Spot my mistake: Reading a weld symbol below the reference line as though it sat above it

PPJ-TDR-00531 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on reading a weld symbol below

Subscribe to unlock all

Spot my mistake: Assuming a plain washer locks a nut against loosening

PPJ-TDR-00534 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a plain washer loc

Subscribe to unlock all

Spot my mistake: Assuming the centre of gravity of a lamina must lie within its outline

PPJ-TDR-00544 Similar prompts

Act as my SS3 Technical Drawing tutor. Write a short answer on assuming the centre of grav

Subscribe to unlock all

Let me explain: Dividing a line in a given ratio

PPJ-TDR-00025 Similar prompts

I have just studied dividing a line in a given ratio in my SS3 Technical Drawing class. Le

Subscribe to unlock all

Let me explain: Enlarging or reducing a figure by area

PPJ-TDR-00095 Similar prompts

I have just studied enlarging or reducing a figure by area in my SS3 Technical Drawing cla

Subscribe to unlock all

Let me explain: Developing the surface of a cylinder

PPJ-TDR-00165 Similar prompts

I have just studied developing the surface of a cylinder in my SS3 Technical Drawing class

Subscribe to unlock all

Let me explain: The drawings that make up a set of working drawings

PPJ-TDR-00225 Similar prompts

I have just studied the drawings that make up a set of working drawings in my SS3 Technica

Subscribe to unlock all

Let me explain: Sketching a building tool in pictorial view

PPJ-TDR-00254 Similar prompts

I have just studied sketching a building tool in pictorial view in my SS3 Technical Drawin

Subscribe to unlock all

Let me explain: The members of a king post truss

PPJ-TDR-00314 Similar prompts

I have just studied the members of a king post truss in my SS3 Technical Drawing class. Le

Subscribe to unlock all

Let me explain: Setting up a two-point perspective

PPJ-TDR-00434 Similar prompts

I have just studied setting up a two-point perspective in my SS3 Technical Drawing class.

Subscribe to unlock all

Let me explain: Projecting a third view from two given views

PPJ-TDR-00444 Similar prompts

I have just studied projecting a third view from two given views in my SS3 Technical Drawi

Subscribe to unlock all

Let me explain: Developing the surface of a frustum

PPJ-TDR-00484 Similar prompts

I have just studied developing the surface of a frustum in my SS3 Technical Drawing class.

Subscribe to unlock all

Let me explain: Finding the centroid of a composite figure

PPJ-TDR-00494 Similar prompts

I have just studied finding the centroid of a composite figure in my SS3 Technical Drawing

Subscribe to unlock all