Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Why hatching lines on a section are drawn at 45 degrees and spaced evenly"
Spot my mistake: 3. Construct a cycloid and a trochoid from a rolling circle
Write a short SS1 Technical Drawing answer about 3. Construct a cycloid and a trochoid fro
Subscribe to unlock allProject task: Concentric-circles method for an ellipse step by step. Students construct an ellipse by all
Give me a practical task on concentric-circles method for an ellipse step by step. Student
Subscribe to unlock allPractice set: Success: ellipse constructed by all three methods
Set me five practice tasks on success: ellipse constructed by all three methods, at the le
Subscribe to unlock allLet me explain: 3. Determine true lengths of the edges of full and truncated solids
I am going to explain 3. Determine true lengths of the edges of full and truncated solids
Subscribe to unlock allWAEC prep: Success: truncated cylinder model assembled
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 2. Draw and interpret the first-angle and third-angle projection symbols
I am revising Orthographic Projection for SS1 Technical Drawing. Test me on 2. Draw and in
Subscribe to unlock allQuiz: 2. Place dimensions on circles, arcs and chamfers
Set me a quick recall test on 2. Place dimensions on circles, arcs and chamfers at SS1 lev
Subscribe to unlock allReal-life Nigeria: Dimensioning rules with examples of correct
Take dimensioning rules with examples of correct out of the textbook. Describe a real Nige
Subscribe to unlock allPractice set: Dimension circles, arcs, chamfers and vertical, horizontal and angular shapes correctly
Set me five practice tasks on dimension circles, arcs, chamfers and vertical, horizontal a
Subscribe to unlock allQuiz: 2. Construct isometric circles as four-centre ellipses in all three isometric planes
I am revising Isometric Drawing II for SS1 Technical Drawing. Test me on 2. Construct isom
Subscribe to unlock allLet me explain: 3. Construct isometric arcs and fillets
Let me talk you through 3. Construct isometric arcs and fillets from the Isometric Drawing
Subscribe to unlock allPractice set: Four-centre ellipse inside an isometric rhombus. Students construct isometric circles in the
Give me a practice set on four-centre ellipse inside an isometric rhombus. Students constr
Subscribe to unlock allLet me explain: 3. Use construction layers to build up complex isometric shapes
I am going to explain 3. Use construction layers to build up complex isometric shapes to y
Subscribe to unlock allQuiz: 3. Construct an oblique drawing using the box method
Quiz me on 3. Construct an oblique drawing using the box method, from the SS1 Technical Dr
Subscribe to unlock allLet me explain: 4. Construct an oblique drawing using the centre-layout method
Act as my study partner. I will teach you 4. Construct an oblique drawing using the centre
Subscribe to unlock allPractice set: Portfolio and board accuracy recorded separately
Set me five practice tasks on portfolio and board accuracy recorded separately, at the lev
Subscribe to unlock allWAEC prep: Producing a hazard-and-control chart
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allWAEC prep: Success: all six diagram pairs correctly judged with a valid geometric reason for each
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all