Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Let me explain: Dividing a line in a given ratio"
WAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: 2. Circumscribe a circle about a given triangle
Give me a wrong or muddled explanation of 2. Circumscribe a circle about a given triangle
Subscribe to unlock allPractice set: Incentre construction using angle bisectors
Give me a practice set on incentre construction using angle bisectors for SS1 Technical Dr
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Marks recorded against each objective
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allReal-life Nigeria: Naming polygons from three to twelve sides
Take naming polygons from three to twelve sides out of the textbook. Describe a real Niger
Subscribe to unlock allPractice set: Each of the three methods for a regular heptagon. Students construct a heptagon by all three
Give me a practice set on each of the three methods for a regular heptagon. Students const
Subscribe to unlock allPractice set: Enlarge and reduce plane figures based on the ratio of areas and verify the result
Set me five practice tasks on enlarge and reduce plane figures based on the ratio of areas
Subscribe to unlock allWAEC prep: Success: all six diagram pairs correctly judged with a valid geometric reason for each
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: all blends visually smooth with tangency points marked and radii within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: crank locus plotted at twelve positions forming a smooth closed curve
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 1. Define and distinguish the ellipse, cycloid, trochoid, involute and helix
I am revising Special Curves for SS1 Technical Drawing. Test me on 1. Define and distingui
Subscribe to unlock allWAEC prep: Success: truncated cylinder model assembled
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 2. Draw and interpret the first-angle and third-angle projection symbols
I am revising Orthographic Projection for SS1 Technical Drawing. Test me on 2. Draw and in
Subscribe to unlock allQuiz: 2. Prepare a title block and border to standard proportions on a drawing sheet
Set me a quick recall test on 2. Prepare a title block and border to standard proportions
Subscribe to unlock allQuiz: 2. Identify hazards in the drawing studio
Quiz me on 2. Identify hazards in the drawing studio, from the SS1 Technical Drawing topic
Subscribe to unlock allPractice set: Demonstrating safe handling of board, T-square and compass
Set me five practice tasks on demonstrating safe handling of board, T-square and compass,
Subscribe to unlock allPractice set: Success: assessed observation checklist passed on all five safety points
Set me five practice tasks on success: assessed observation checklist passed on all five s
Subscribe to unlock allQuiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock all