Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →296 prompts matching "Calculating the number of risers for a 3000 mm rise at 150 mm per riser"
WAEC prep: The rules governing rise and going
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allWAEC prep: Lintels over openings and their bearing
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allWAEC prep: Sanitary fittings and their drainage
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allWAEC prep: The hole basis and shaft basis systems
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allLet me explain: The part or local section
I have just studied the part or local section in my SS3 Technical Drawing class. Let me ex
Subscribe to unlock allWAEC prep: The aligned section and when it is proper
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allLet me explain: Drawing an isometric circle by the four-centre method
I have just studied drawing an isometric circle by the four-centre method in my SS3 Technical Drawing class. Let me explain it back to you in my own words, then tell me plainly what I got wrong or left out. Ask me one follow-up question afterwards to test whether I really understood it.
launch and paste in:
WAEC prep: Non-isometric lines and how they are plotted
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allWAEC prep: The angle a line makes with the horizontal plane
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allWAEC prep: The angle between two intersecting planes
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allSpot my mistake: A drawing that misuses a standard symbol
Act as my SS3 Technical Drawing tutor. Write a short answer on a drawing that misuses a st
Subscribe to unlock allSpot my mistake: Assuming a single set square will give every angle a drawing requires
Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a single set squar
Subscribe to unlock allSpot my mistake: Using a chain line where a hidden edge should be shown
Act as my SS3 Technical Drawing tutor. Write a short answer on using a chain line where a
Subscribe to unlock allSpot my mistake: Assuming any angle can be constructed with compasses by repeated bisection
Act as my SS3 Technical Drawing tutor. Write a short answer on assuming any angle can be c
Subscribe to unlock allSpot my mistake: Assuming a polygon constructed on a given side will also fit a given circle
Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a polygon construc
Subscribe to unlock allSpot my mistake: Treating an isometric drawing as a perspective view with lines converging on a vanishing point
Act as my SS3 Technical Drawing tutor. Write a short answer on treating an isometric drawi
Subscribe to unlock allSpot my mistake: Deciding a frame member is a tie because it is horizontal
Act as my SS3 Technical Drawing tutor. Write a short answer on deciding a frame member is
Subscribe to unlock allSpot my mistake: Dimensioning every part fully on an assembly drawing
Act as my SS3 Technical Drawing tutor. Write a short answer on dimensioning every part ful
Subscribe to unlock allSpot my mistake: Assuming every wall in a building carries load
Act as my SS3 Technical Drawing tutor. Write a short answer on assuming every wall in a bu
Subscribe to unlock allSpot my mistake: Assuming a transition fit always leaves clearance
Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a transition fit a
Subscribe to unlock all