Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →226 prompts matching "Annotating a joint with the correct weld symbol"
Practice set: Revision: timed construction drills, board-work clinic on weak constructions
Give me a practice set on revision: timed construction drills, board-work clinic on weak c
Subscribe to unlock allWAEC prep: Marks recorded against each objective
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Define a polygon
Be my SS1 Technical Drawing teacher for this one point: 1. Define a polygon. Start with wh
Subscribe to unlock allLet me explain: 3. Construct a plain scale to a given representative fraction
I am going to explain 3. Construct a plain scale to a given representative fraction to you
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allTeach me: 2. Construct a rectangle equal in area to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 2. Construct a rectangle equal in
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allQuiz: 3. Construct an arc tangent to a straight line
I am revising Tangents and Tangency I for SS1 Technical Drawing. Test me on 3. Construct a
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock allSpot my mistake: 1. Define a locus
Give me a wrong or muddled explanation of 1. Define a locus from the Loci and Simple Mecha
Subscribe to unlock allWAEC prep: Success: crank locus plotted at twelve positions forming a smooth closed curve
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Concentric-circles method for an ellipse step by step. Students construct an ellipse by all
Give me a practical task on concentric-circles method for an ellipse step by step. Student
Subscribe to unlock allWAEC prep: Constructing an ellipse by three methods and a cycloid
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Preparing pyramid and cone developments
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Set out parallel-line developments for a truncated hexagonal prism
Give me a practice set on set out parallel-line developments for a truncated hexagonal pri
Subscribe to unlock allWAEC prep: Success: truncated cylinder model assembled
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Explain orthographic projection and distinguish first-angle from third-angle projection
You are my personal SS1 Technical Drawing tutor. Teach me 1. Explain orthographic projecti
Subscribe to unlock all