Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "The isometric axes and how a solid is set out on them"
Spot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allSpot my mistake: 4. Identify the constructions used to transfer area between shapes
Give me a wrong or muddled explanation of 4. Identify the constructions used to transfer a
Subscribe to unlock allTeach me: 1. State the rules and conventions of dimensioning
I am an SS1 student studying Methods of Dimensioning in Technical Drawing. Explain 1. Stat
Subscribe to unlock allWAEC prep: The two classifications of drawing, compared
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: sheet completed with correct pencil grade for outline, construction and dimension lines
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allWAEC prep: Success: all letters within ±0.5 mm of the guide-line height with uniform stroke thickness
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Producing a hazard-and-control chart
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allWAEC prep: Five standard abbreviations with meanings
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: sides of the heptagon equal within 0.5 mm by at least two of the three methods
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Why doubling the area of a square requires a side ratio of √2
Give me a practical task on why doubling the area of a square requires a side ratio of √2
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Constructing an ellipse by three methods and a cycloid
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Preparing pyramid and cone developments
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Promotion decision informed by objective-level analysis
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allReal-life Nigeria: Drawing a large circle and label all named parts
Take drawing a large circle and label all named parts out of the textbook. Describe a real
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock all