Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →218 prompts matching "Drawing the lines of intersection of two square prisms meeting at 90 degrees"
Teach me: 1. Arrange an appropriate working area before starting a drawing
I am an SS1 student studying Board Practice: Title Block and Lettering in Technical Drawin
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allPractice set: Constructing triangles from all three sets of given data
Set me five practice tasks on constructing triangles from all three sets of given data, at
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 3. Construct the special quadrilaterals to given dimensions
You are my personal SS1 Technical Drawing tutor. Teach me 3. Construct the special quadril
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allPractice set: Accuracy of construction assessed separately from knowledge
Set me five practice tasks on accuracy of construction assessed separately from knowledge,
Subscribe to unlock allQuiz: 2. Construct a regular polygon using the circle (circumscribing) method
I am revising Polygons II for SS1 Technical Drawing. Test me on 2. Construct a regular pol
Subscribe to unlock allSpot my mistake: 4. Compare the three methods for accuracy
Write a short SS1 Technical Drawing answer about 4. Compare the three methods for accuracy
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allSpot my mistake: 4. Identify the constructions used to transfer area between shapes
Give me a wrong or muddled explanation of 4. Identify the constructions used to transfer a
Subscribe to unlock allPractice set: Success: radius and tangent perpendicular within ±1° at every point of tangency
Set me five practice tasks on success: radius and tangent perpendicular within ±1° at ever
Subscribe to unlock allQuiz: 3. Construct an arc touching one circle internally and enclosing the other externally
Set me a quick recall test on 3. Construct an arc touching one circle internally and enclo
Subscribe to unlock allLet me explain: 4. Relate loci to the motion produced by levers, linkages and rotary systems
Act as my study partner. I will teach you 4. Relate loci to the motion produced by levers,
Subscribe to unlock allQuiz: 1. Define and distinguish the ellipse, cycloid, trochoid, involute and helix
I am revising Special Curves for SS1 Technical Drawing. Test me on 1. Define and distingui
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allQuiz: 2. Draw and interpret the first-angle and third-angle projection symbols
I am revising Orthographic Projection for SS1 Technical Drawing. Test me on 2. Draw and in
Subscribe to unlock all