Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →204 prompts matching "Drawing a four-bar linkage to given link lengths and set out twelve crank positi"
Teach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allQuiz: 2. Distinguish between enlargement by ratio of sides and by ratio of areas
Quiz me on 2. Distinguish between enlargement by ratio of sides and by ratio of areas, fro
Subscribe to unlock allLet me explain: 3. Apply the radial (ray) method of enlargement from a chosen pole
Let me talk you through 3. Apply the radial (ray) method of enlargement from a chosen pole
Subscribe to unlock allSpot my mistake: 4. Verify the accuracy of an enlargement by measurement and calculation
Write a short SS1 Technical Drawing answer about 4. Verify the accuracy of an enlargement
Subscribe to unlock allReal-life Nigeria: Enlarge an irregular pentagon in the ratio of areas 3:2
Show me how enlarge an irregular pentagon in the ratio of areas 3:2 works in real life in
Subscribe to unlock allTeach me: 1. Outline the principles of determining figures of equal area
I am an SS1 student studying Equal Areas of Similar Figures I in Technical Drawing. Explai
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allLet me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock allTeach me: 2. Plot the locus of a point on a rotating and a sliding mechanism
Be my SS1 Technical Drawing teacher for this one point: 2. Plot the locus of a point on a
Subscribe to unlock allQuiz: 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism
Quiz me on 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism, fr
Subscribe to unlock allTeach me: Formal assessment of the second term programme of study
You are my personal SS1 Technical Drawing tutor. Teach me formal assessment of the second
Subscribe to unlock allSpot my mistake: 3. Construct a cycloid and a trochoid from a rolling circle
Write a short SS1 Technical Drawing answer about 3. Construct a cycloid and a trochoid fro
Subscribe to unlock allTeach me: 4. State the engineering applications of each special curve
I am an SS1 student studying Special Curves in Technical Drawing. Explain 4. State the eng
Subscribe to unlock allSpot my mistake: 4. Prepare the pattern development of a pyramid and of a cone
Give me a wrong or muddled explanation of 4. Prepare the pattern development of a pyramid
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allTeach me: 1. Explain orthographic projection and distinguish first-angle from third-angle projection
You are my personal SS1 Technical Drawing tutor. Teach me 1. Explain orthographic projecti
Subscribe to unlock allTeach me: 1. State the rules and conventions of dimensioning
I am an SS1 student studying Methods of Dimensioning in Technical Drawing. Explain 1. Stat
Subscribe to unlock allLet me explain: 3. Place dimensions on vertical, horizontal and angular features
I am going to explain 3. Place dimensions on vertical, horizontal and angular features to
Subscribe to unlock allTeach me: 1. Construct isometric squares and rectangles by the box method
You are my personal SS1 Technical Drawing tutor. Teach me 1. Construct isometric squares a
Subscribe to unlock allLet me explain: 3. Construct isometric arcs and fillets
Let me talk you through 3. Construct isometric arcs and fillets from the Isometric Drawing
Subscribe to unlock all