Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "What a tolerance is and why it is specified"
Practice set: Demonstrating safe handling of board, T-square and compass
Set me five practice tasks on demonstrating safe handling of board, T-square and compass,
Subscribe to unlock allWAEC prep: Producing a hazard-and-control chart
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Identify the types of lines used in technical drawing and the purpose and weight of each
You are my personal SS1 Technical Drawing tutor. Teach me 1. Identify the types of lines u
Subscribe to unlock allQuiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allPractice set: Constructing the special angles without a protractor
Set me five practice tasks on constructing the special angles without a protractor, at the
Subscribe to unlock allTeach me: Given one side and two angles
You are my personal SS1 Technical Drawing tutor. Teach me given one side and two angles, a
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock allSpot my mistake: 2. Circumscribe a circle about a given triangle
Give me a wrong or muddled explanation of 2. Circumscribe a circle about a given triangle
Subscribe to unlock allQuiz: 4. Explain the geometric basis of each construction using bisectors
Quiz me on 4. Explain the geometric basis of each construction using bisectors, from the S
Subscribe to unlock allPractice set: Incentre construction using angle bisectors
Give me a practice set on incentre construction using angle bisectors for SS1 Technical Dr
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 4. Construct any quadrilateral when four sides and one diagonal are known
I am revising Quadrilaterals for SS1 Technical Drawing. Test me on 4. Construct any quadri
Subscribe to unlock allPractice set: The types of quadrilaterals with their properties
Set me five practice tasks on the types of quadrilaterals with their properties, at the le
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allReal-life Nigeria: Standard line-type and abbreviation tables. Students produce a reference sheet showing sheet
Show me how standard line-type and abbreviation tables. Students produce a reference sheet
Subscribe to unlock all