Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →216 prompts matching "The sequence of commands used to obtain the auxiliary view"
Practice set: Preparing a title block to given proportions
Set me five practice tasks on preparing a title block to given proportions, at the level e
Subscribe to unlock allQuiz: 2. Identify hazards in the drawing studio
Quiz me on 2. Identify hazards in the drawing studio, from the SS1 Technical Drawing topic
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock allTeach me: 3. Describe an escribed circle and construct one to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 3. Describe an escribed circle and
Subscribe to unlock allPractice set: Incentre construction using angle bisectors
Give me a practice set on incentre construction using angle bisectors for SS1 Technical Dr
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: 2. Identify standard line types and their applications as set out in the drawing standard
Write a short SS1 Technical Drawing answer about 2. Identify standard line types and their
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allPractice set: Success: both projection symbols drawn to correct proportion and correctly identified
Set me five practice tasks on success: both projection symbols drawn to correct proportion
Subscribe to unlock allTeach me: 1. Construct a regular polygon using the square (general) method
You are my personal SS1 Technical Drawing tutor. Teach me 1. Construct a regular polygon u
Subscribe to unlock allSpot my mistake: 4. Compare the three methods for accuracy
Write a short SS1 Technical Drawing answer about 4. Compare the three methods for accuracy
Subscribe to unlock allLet me explain: 3. Construct a plain scale to a given representative fraction
I am going to explain 3. Construct a plain scale to a given representative fraction to you
Subscribe to unlock allWAEC prep: Success: all five scale-factor calculations correct to two decimal places
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allQuiz: 3. Construct an arc tangent to a straight line
I am revising Tangents and Tangency I for SS1 Technical Drawing. Test me on 3. Construct a
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock all