Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →214 prompts matching "The conic section produced by each of four stated cutting planes on a cone"
Spot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allPractice set: Constructing the special angles without a protractor
Set me five practice tasks on constructing the special angles without a protractor, at the
Subscribe to unlock allTeach me: 1. Define a triangle
Be my SS1 Technical Drawing teacher for this one point: 1. Define a triangle. Start with w
Subscribe to unlock allTeach me: Given one side and two angles
You are my personal SS1 Technical Drawing tutor. Teach me given one side and two angles, a
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allTeach me: 3. Distinguish eccentric from concentric circles and illustrate each
I am an SS1 student studying Circles and Triangles I in Technical Drawing. Explain 3. Dist
Subscribe to unlock allTeach me: 3. Describe an escribed circle and construct one to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 3. Describe an escribed circle and
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock allWAEC prep: Marks recorded against each objective
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Define a polygon
Be my SS1 Technical Drawing teacher for this one point: 1. Define a polygon. Start with wh
Subscribe to unlock allQuiz: 2. Construct a regular polygon using the circle (circumscribing) method
I am revising Polygons II for SS1 Technical Drawing. Test me on 2. Construct a regular pol
Subscribe to unlock allLet me explain: 3. Construct a regular polygon using the diagonal method
Let me talk you through 3. Construct a regular polygon using the diagonal method from the
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allSpot my mistake: 4. Identify the constructions used to transfer area between shapes
Give me a wrong or muddled explanation of 4. Identify the constructions used to transfer a
Subscribe to unlock allWAEC prep: Success: all six diagram pairs correctly judged with a valid geometric reason for each
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allLet me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock all