Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Quiz: Drawing a slider-crank mechanism and plot the locus of the mid-point of th"
WAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 3. Construct the special quadrilaterals to given dimensions
You are my personal SS1 Technical Drawing tutor. Teach me 3. Construct the special quadril
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allPractice set: Sheet sizes and line types
Set me five practice tasks on sheet sizes and line types, at the level expected in SS1 Dra
Subscribe to unlock allWAEC prep: Five standard abbreviations with meanings
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Success: both projection symbols drawn to correct proportion and correctly identified
Set me five practice tasks on success: both projection symbols drawn to correct proportion
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock allTeach me: 1. Construct a regular polygon using the square (general) method
You are my personal SS1 Technical Drawing tutor. Teach me 1. Construct a regular polygon u
Subscribe to unlock allLet me explain: 3. Construct a regular polygon using the diagonal method
Let me talk you through 3. Construct a regular polygon using the diagonal method from the
Subscribe to unlock allSpot my mistake: 4. Compare the three methods for accuracy
Write a short SS1 Technical Drawing answer about 4. Compare the three methods for accuracy
Subscribe to unlock allPractice set: Each of the three methods for a regular heptagon. Students construct a heptagon by all three
Give me a practice set on each of the three methods for a regular heptagon. Students const
Subscribe to unlock allWAEC prep: Success: sides of the heptagon equal within 0.5 mm by at least two of the three methods
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Why doubling the area of a square requires a side ratio of √2
Give me a practical task on why doubling the area of a square requires a side ratio of √2
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allLet me explain: 3. Apply the radial (ray) method of enlargement from a chosen pole
Let me talk you through 3. Apply the radial (ray) method of enlargement from a chosen pole
Subscribe to unlock allReal-life Nigeria: Enlarge an irregular pentagon in the ratio of areas 3:2
Show me how enlarge an irregular pentagon in the ratio of areas 3:2 works in real life in
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allQuiz: 3. Construct an arc tangent to a straight line
I am revising Tangents and Tangency I for SS1 Technical Drawing. Test me on 3. Construct a
Subscribe to unlock allLet me explain: 4. Construct common tangents to two equal and to two unequal circles
Let me talk you through 4. Construct common tangents to two equal and to two unequal circl
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all