Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →287 prompts matching "Producing an assembly from given detail drawings"
Quiz: On the same detail the damp-proof course
I am revising Building Details I for SS2 Technical Drawing. Test me on on the same detail
Subscribe to unlock allPractice set: Detail on the board one layer at a time
Give me a practice set on detail on the board one layer at a time for SS2 Technical Drawin
Subscribe to unlock allQuiz: Assessed AO2, and roof types and members recur in WAEC and NECO
Quiz me on assessed AO2, and roof types and members recur in WAEC and NECO, from the SS2 T
Subscribe to unlock allQuiz: The parabola, hyperbola, involute and cycloid by the defining condition of each, compared
I am revising Loci and Special Curves for SS2 Technical Drawing. Test me on the parabola,
Subscribe to unlock allPractice set: Comparing the two curves and account for any difference
Give me a practice set on comparing the two curves and account for any difference for SS2
Subscribe to unlock allWAEC prep: The difference between the eccentricity of a parabola and that of a hyperbola
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allTeach me: Constructing an epicycloid and a hypocycloid on a stated directing circle
You are my personal SS2 Technical Drawing tutor. Teach me constructing an epicycloid and a
Subscribe to unlock allQuiz: Assessed AO2 and AO3
I am revising Constructing Special Curves II for SS2 Technical Drawing. Test me on assesse
Subscribe to unlock allReal-life Nigeria: Constructing an involute of a circle and a cycloid on one A3 sheet
Take constructing an involute of a circle and a cycloid on one A3 sheet out of the textboo
Subscribe to unlock allReal-life Nigeria: Checking each other's stroke measurement against the calculated value of twice the crank radius
Take checking each other's stroke measurement against the calculated value of twice the cr
Subscribe to unlock allWAEC prep: Plotting the locus of the mid-point of the connecting rod for twelve crank positions
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock allTeach me: What is meant by the true shape of a cut surface
You are my personal SS2 Technical Drawing tutor. Teach me what is meant by the true shape
Subscribe to unlock allSpot my mistake: The conic section produced by each of four stated cutting planes on a cone
Write a short SS2 Technical Drawing answer about the conic section produced by each of fou
Subscribe to unlock allPractice set: Modelling-clay cone at four angles in front of the class
Give me a practice set on modelling-clay cone at four angles in front of the class for SS2
Subscribe to unlock allReal-life Nigeria: Measuring the major and minor axes of their ellipse
Show me how measuring the major and minor axes of their ellipse works in real life in Nige
Subscribe to unlock allLet me explain: Determine the true shape of the cut face of a square pyramid truncated by an inclined plane
I am going to explain determine the true shape of the cut face of a square pyramid truncat
Subscribe to unlock allSpot my mistake: Project the true shape of a cut face on a pentagonal pyramid where the cutting plane passes
Give me a wrong or muddled explanation of project the true shape of a cut face on a pentag
Subscribe to unlock allProject task: Drawing a 40 mm side hexagonal prism 80 mm high truncated at 35 degrees
Set me a small project on drawing a 40 mm side hexagonal prism 80 mm high truncated at 35
Subscribe to unlock allReal-life Nigeria: Swap sheets and mark each other's work against a three-point checklist
Take swap sheets and mark each other's work against a three-point checklist out of the tex
Subscribe to unlock allWAEC prep: Drawing the true shape of the cut face of a square pyramid of 50 mm base truncated at 40
Act as my WAEC Technical Drawing examiner. I am in SS2. Set me an exam-standard question o
Subscribe to unlock all