Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Drawing the involute of a square of 30 mm side and measure the length of the fin"
Quiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allTeach me: 2. Construct an arc of given radius externally enclosing two circles
I am an SS1 student studying Tangents and Tangency II in Technical Drawing. Explain 2. Con
Subscribe to unlock allLet me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock allWAEC prep: Success: all blends visually smooth with tangency points marked and radii within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allReal-life Nigeria: Dimensioning rules with examples of correct
Take dimensioning rules with examples of correct out of the textbook. Describe a real Nige
Subscribe to unlock allWAEC prep: Success: all three solids drawn with axes at 30° ±1°
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Constructing isometric squares, rectangles, arcs and circles
Set me five practice tasks on constructing isometric squares, rectangles, arcs and circles
Subscribe to unlock allQuiz: 2. Distinguish between drawing materials and drawing instruments
I am revising Drawing Materials and Equipment for SS1 Technical Drawing. Test me on 2. Dis
Subscribe to unlock allPractice set: And names each item in a full drawing set
Give me a practice set on and names each item in a full drawing set for SS1 Technical Draw
Subscribe to unlock allTeach me: 1. Arrange an appropriate working area before starting a drawing
I am an SS1 student studying Board Practice: Title Block and Lettering in Technical Drawin
Subscribe to unlock allQuiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allLet me explain: 3. Construct a triangle given three sides
Act as my study partner. I will teach you 3. Construct a triangle given three sides in my
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allPractice set: Constructing triangles from all three sets of given data
Set me five practice tasks on constructing triangles from all three sets of given data, at
Subscribe to unlock allPractice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock all