Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Calculating the number of risers for a 3000 mm rise at 150 mm per riser"
Quiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allSpot my mistake: Constructing an inscribed, a circumscribed and an escribed circle for a given triangle
Show me a worked example on constructing an inscribed, a circumscribed and an escribed cir
Subscribe to unlock allTeach me: 3. Construct the special quadrilaterals to given dimensions
You are my personal SS1 Technical Drawing tutor. Teach me 3. Construct the special quadril
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allLet me explain: Consolidation of drawing practice, line work
I am going to explain consolidation of drawing practice, line work to you, as an SS1 Techn
Subscribe to unlock allTeach me: 1. Construct a regular polygon using the square (general) method
You are my personal SS1 Technical Drawing tutor. Teach me 1. Construct a regular polygon u
Subscribe to unlock allQuiz: 2. Construct a regular polygon using the circle (circumscribing) method
I am revising Polygons II for SS1 Technical Drawing. Test me on 2. Construct a regular pol
Subscribe to unlock allLet me explain: 3. Construct a regular polygon using the diagonal method
Let me talk you through 3. Construct a regular polygon using the diagonal method from the
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allSpot my mistake: 4. Identify the constructions used to transfer area between shapes
Give me a wrong or muddled explanation of 4. Identify the constructions used to transfer a
Subscribe to unlock allWAEC prep: Success: all six diagram pairs correctly judged with a valid geometric reason for each
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 4. Convert a given irregular polygon into a triangle of equal area and verify by calculation
Act as my study partner. I will teach you 4. Convert a given irregular polygon into a tria
Subscribe to unlock allPractice set: Completing the four standard equal-area constructions on one sheet
Give me a practice set on completing the four standard equal-area constructions on one she
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allQuiz: 3. Construct an arc touching one circle internally and enclosing the other externally
Set me a quick recall test on 3. Construct an arc touching one circle internally and enclo
Subscribe to unlock allLet me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock allSpot my mistake: Constructing arcs internally touching, externally enclosing and mixed for two circles
Show me a worked example on constructing arcs internally touching, externally enclosing an
Subscribe to unlock allWAEC prep: Success: all blends visually smooth with tangency points marked and radii within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all