Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →214 prompts matching "What the centre of gravity of a lamina means"
Let me explain: 4. Blend arcs and lines smoothly, marking all points of tangency
I am going to explain 4. Blend arcs and lines smoothly, marking all points of tangency to
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allProject task: Three views of a stepped block from a physical model
Set me a small project on three views of a stepped block from a physical model, the kind I
Subscribe to unlock allSpot my mistake: 4. Distinguish chain, parallel and running dimensioning and select the appropriate system
Give me a wrong or muddled explanation of 4. Distinguish chain, parallel and running dimen
Subscribe to unlock allReal-life Nigeria: Dimensioning rules with examples of correct
Take dimensioning rules with examples of correct out of the textbook. Describe a real Nige
Subscribe to unlock allSpot my mistake: 4. Produce a finished isometric drawing of a composite object from orthographic views
Give me a wrong or muddled explanation of 4. Produce a finished isometric drawing of a com
Subscribe to unlock allSpot my mistake: 4. Use drawing materials and instruments correctly to produce simple drawings of objects
Write a short SS1 Technical Drawing answer about 4. Use drawing materials and instruments
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allPractice set: Constructing the special angles without a protractor
Set me five practice tasks on constructing the special angles without a protractor, at the
Subscribe to unlock allPractice set: Incentre construction using angle bisectors
Give me a practice set on incentre construction using angle bisectors for SS1 Technical Dr
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Five standard abbreviations with meanings
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 2. Distinguish between enlargement by ratio of sides and by ratio of areas
Quiz me on 2. Distinguish between enlargement by ratio of sides and by ratio of areas, fro
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allTeach me: 2. Construct an arc of given radius externally enclosing two circles
I am an SS1 student studying Tangents and Tangency II in Technical Drawing. Explain 2. Con
Subscribe to unlock all