Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →215 prompts matching "Drawing the true helix of a screw thread rather than its conventional representa"
Spot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allReal-life Nigeria: Drawing a large circle and label all named parts
Take drawing a large circle and label all named parts out of the textbook. Describe a real
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 3. Construct a regular polygon using the diagonal method
Let me talk you through 3. Construct a regular polygon using the diagonal method from the
Subscribe to unlock allQuiz: 2. Distinguish between enlargement by ratio of sides and by ratio of areas
Quiz me on 2. Distinguish between enlargement by ratio of sides and by ratio of areas, fro
Subscribe to unlock allTeach me: 1. Enlarge a given plane figure based on a ratio of areas
You are my personal SS1 Technical Drawing tutor. Teach me 1. Enlarge a given plane figure
Subscribe to unlock allQuiz: 2. Reduce a given plane figure based on a ratio of areas
I am revising Enlargement and Reduction II for SS1 Technical Drawing. Test me on 2. Reduce
Subscribe to unlock allSpot my mistake: 1. Construct an arc of given radius internally touching two circles
Write a short SS1 Technical Drawing answer about 1. Construct an arc of given radius inter
Subscribe to unlock allTeach me: 2. Construct an arc of given radius externally enclosing two circles
I am an SS1 student studying Tangents and Tangency II in Technical Drawing. Explain 2. Con
Subscribe to unlock allReal-life Nigeria: Work through the three arc-tangency cases from given data
Take work through the three arc-tangency cases from given data out of the textbook. Descri
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allReal-life Nigeria: Dimensioning rules with examples of correct
Take dimensioning rules with examples of correct out of the textbook. Describe a real Nige
Subscribe to unlock allQuiz: 2. Distinguish between drawing materials and drawing instruments
I am revising Drawing Materials and Equipment for SS1 Technical Drawing. Test me on 2. Dis
Subscribe to unlock allPractice set: And names each item in a full drawing set
Give me a practice set on and names each item in a full drawing set for SS1 Technical Draw
Subscribe to unlock allTeach me: 1. Arrange an appropriate working area before starting a drawing
I am an SS1 student studying Board Practice: Title Block and Lettering in Technical Drawin
Subscribe to unlock allQuiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all