Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Drawing a stepped block in two-point perspective with vanishing points 300 mm ap"
Practice set: Completing the four standard equal-area constructions on one sheet
Give me a practice set on completing the four standard equal-area constructions on one she
Subscribe to unlock allTeach me: 1. Prepare the pattern development of a prism and of a cylinder
Be my SS1 Technical Drawing teacher for this one point: 1. Prepare the pattern development
Subscribe to unlock allPractice set: Set out parallel-line developments for a truncated hexagonal prism
Give me a practice set on set out parallel-line developments for a truncated hexagonal pri
Subscribe to unlock allPractice set: Four-centre ellipse inside an isometric rhombus. Students construct isometric circles in the
Give me a practice set on four-centre ellipse inside an isometric rhombus. Students constr
Subscribe to unlock allPractice set: Two advantages of CADD
Set me five practice tasks on two advantages of CADD, at the level expected in SS1 Drawing
Subscribe to unlock allLet me explain: 3. Describe the purpose of lettering
I am going to explain 3. Describe the purpose of lettering to you, as an SS1 Technical Dra
Subscribe to unlock allWAEC prep: Producing a hazard-and-control chart
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Marks recorded against each objective
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Construct a regular polygon using the square (general) method
You are my personal SS1 Technical Drawing tutor. Teach me 1. Construct a regular polygon u
Subscribe to unlock allQuiz: 2. Construct a regular polygon using the circle (circumscribing) method
I am revising Polygons II for SS1 Technical Drawing. Test me on 2. Construct a regular pol
Subscribe to unlock allProject task: Why doubling the area of a square requires a side ratio of √2
Give me a practical task on why doubling the area of a square requires a side ratio of √2
Subscribe to unlock allWAEC prep: Success: all six diagram pairs correctly judged with a valid geometric reason for each
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 3. Construct an arc tangent to a straight line
I am revising Tangents and Tangency I for SS1 Technical Drawing. Test me on 3. Construct a
Subscribe to unlock allWAEC prep: Success: crank locus plotted at twelve positions forming a smooth closed curve
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 1. Define and distinguish the ellipse, cycloid, trochoid, involute and helix
I am revising Special Curves for SS1 Technical Drawing. Test me on 1. Define and distingui
Subscribe to unlock allWAEC prep: Constructing an ellipse by three methods and a cycloid
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock all