Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →225 prompts matching "Quiz: Metric, square and acme thread forms"
WAEC prep: Producing a hazard-and-control chart
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Identify the types of lines used in technical drawing and the purpose and weight of each
You are my personal SS1 Technical Drawing tutor. Teach me 1. Identify the types of lines u
Subscribe to unlock allQuiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allSpot my mistake: And produce all six line types at correct weight
Show me a worked example on and produce all six line types at correct weight with an error
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allSpot my mistake: Given two sides and the included angle
Show me a worked example on given two sides and the included angle with an error somewhere
Subscribe to unlock allTeach me: Given one side and two angles
You are my personal SS1 Technical Drawing tutor. Teach me given one side and two angles, a
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allSpot my mistake: Success: all three constructions within 0.5 mm and ±1° of the specified data
Show me a worked example on success: all three constructions within 0.5 mm and ±1° of the
Subscribe to unlock allSpot my mistake: 2. Draw a circle and label its parts correctly
Write a short SS1 Technical Drawing answer about 2. Draw a circle and label its parts corr
Subscribe to unlock allTeach me: 3. Distinguish eccentric from concentric circles and illustrate each
I am an SS1 student studying Circles and Triangles I in Technical Drawing. Explain 3. Dist
Subscribe to unlock allReal-life Nigeria: Drawing a large circle and label all named parts
Take drawing a large circle and label all named parts out of the textbook. Describe a real
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Success: all ten circle parts correctly labelled and spacings accurate to 0.5 mm
Set me five practice tasks on success: all ten circle parts correctly labelled and spacing
Subscribe to unlock allTeach me: 3. Describe an escribed circle and construct one to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 3. Describe an escribed circle and
Subscribe to unlock allSpot my mistake: Constructing an inscribed, a circumscribed and an escribed circle for a given triangle
Show me a worked example on constructing an inscribed, a circumscribed and an escribed cir
Subscribe to unlock allSpot my mistake: Constructing special quadrilaterals and one from four sides and a diagonal
Show me a worked example on constructing special quadrilaterals and one from four sides an
Subscribe to unlock all