Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Lesson with the load path from roof to soil, drawing it as arrows on a board sec"
Teach me: 1. Describe the uses of scale in technical drawing
I am an SS1 student studying Scales in Technical Drawing. Explain 1. Describe the uses of
Subscribe to unlock allSpot my mistake: 4. Construct a diagonal scale and use it to read to three units of measurement
Give me a wrong or muddled explanation of 4. Construct a diagonal scale and use it to read
Subscribe to unlock allProject task: Why doubling the area of a square requires a side ratio of √2
Give me a practical task on why doubling the area of a square requires a side ratio of √2
Subscribe to unlock allWAEC prep: Success: all five scale-factor calculations correct to two decimal places
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Outline the principles of determining figures of equal area
I am an SS1 student studying Equal Areas of Similar Figures I in Technical Drawing. Explai
Subscribe to unlock allQuiz: 3. Construct a square equal in area to a given rectangle
Quiz me on 3. Construct a square equal in area to a given rectangle, from the SS1 Technica
Subscribe to unlock allQuiz: 3. Construct an arc tangent to a straight line
I am revising Tangents and Tangency I for SS1 Technical Drawing. Test me on 3. Construct a
Subscribe to unlock allLet me explain: 4. Construct common tangents to two equal and to two unequal circles
Let me talk you through 4. Construct common tangents to two equal and to two unequal circl
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allPractice set: Success: radius and tangent perpendicular within ±1° at every point of tangency
Set me five practice tasks on success: radius and tangent perpendicular within ±1° at ever
Subscribe to unlock allQuiz: 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism
Quiz me on 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism, fr
Subscribe to unlock allTeach me: Formal assessment of the second term programme of study
You are my personal SS1 Technical Drawing tutor. Teach me formal assessment of the second
Subscribe to unlock allLet me explain: 2. Construct an ellipse by the four-centre, concentric-circles and parallelogram methods
Let me talk you through 2. Construct an ellipse by the four-centre, concentric-circles and
Subscribe to unlock allSpot my mistake: 3. Construct a cycloid and a trochoid from a rolling circle
Write a short SS1 Technical Drawing answer about 3. Construct a cycloid and a trochoid fro
Subscribe to unlock allTeach me: 4. State the engineering applications of each special curve
I am an SS1 student studying Special Curves in Technical Drawing. Explain 4. State the eng
Subscribe to unlock allSpot my mistake: 4. Prepare the pattern development of a pyramid and of a cone
Give me a wrong or muddled explanation of 4. Prepare the pattern development of a pyramid
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allQuiz: 2. Prepare the development of truncated prisms and cylinders
Quiz me on 2. Prepare the development of truncated prisms and cylinders, from the SS1 Tech
Subscribe to unlock allLet me explain: 3. Produce the front elevation, end elevation and plan of a given solid in first angle
Let me talk you through 3. Produce the front elevation, end elevation and plan of a given
Subscribe to unlock allProject task: Three views of a stepped block from a physical model
Set me a small project on three views of a stepped block from a physical model, the kind I
Subscribe to unlock all