Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →212 prompts matching "Visual ray method, drawing rays from the station point through each plan corner"
Teach me: 1. Arrange an appropriate working area before starting a drawing
I am an SS1 student studying Board Practice: Title Block and Lettering in Technical Drawin
Subscribe to unlock allProject task: Layout of a title block on the board with proportions marked. Students draw a border
Give me a practical task on layout of a title block on the board with proportions marked.
Subscribe to unlock allTeach me: 3. Distinguish eccentric from concentric circles and illustrate each
I am an SS1 student studying Circles and Triangles I in Technical Drawing. Explain 3. Dist
Subscribe to unlock allQuiz: 4. Explain the geometric basis of each construction using bisectors
Quiz me on 4. Explain the geometric basis of each construction using bisectors, from the S
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allQuiz: 2. Distinguish regular from irregular polygons
Quiz me on 2. Distinguish regular from irregular polygons, from the SS1 Technical Drawing
Subscribe to unlock allReal-life Nigeria: Naming polygons from three to twelve sides
Take naming polygons from three to twelve sides out of the textbook. Describe a real Niger
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allProject task: Why doubling the area of a square requires a side ratio of √2
Give me a practical task on why doubling the area of a square requires a side ratio of √2
Subscribe to unlock allTeach me: 1. Outline the principles of determining figures of equal area
I am an SS1 student studying Equal Areas of Similar Figures I in Technical Drawing. Explai
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allWAEC prep: Success: all blends visually smooth with tangency points marked and radii within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 2. Plot the locus of a point on a rotating and a sliding mechanism
Be my SS1 Technical Drawing teacher for this one point: 2. Plot the locus of a point on a
Subscribe to unlock allQuiz: 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism
Quiz me on 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism, fr
Subscribe to unlock allSpot my mistake: 3. Construct a cycloid and a trochoid from a rolling circle
Write a short SS1 Technical Drawing answer about 3. Construct a cycloid and a trochoid fro
Subscribe to unlock allTeach me: 4. State the engineering applications of each special curve
I am an SS1 student studying Special Curves in Technical Drawing. Explain 4. State the eng
Subscribe to unlock allWAEC prep: Constructing an ellipse by three methods and a cycloid
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Prepare the pattern development of a prism and of a cylinder
Be my SS1 Technical Drawing teacher for this one point: 1. Prepare the pattern development
Subscribe to unlock allQuiz: 2. Prepare the development of truncated prisms and cylinders
Quiz me on 2. Prepare the development of truncated prisms and cylinders, from the SS1 Tech
Subscribe to unlock all