Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Setting up a drawing sheet with border and title block"
Teach me: Given one side and two angles
You are my personal SS1 Technical Drawing tutor. Teach me given one side and two angles, a
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allWAEC prep: The classification of triangles by side and by angle
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 3. Describe an escribed circle and construct one to a given triangle
Be my SS1 Technical Drawing teacher for this one point: 3. Describe an escribed circle and
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allQuiz: 4. Construct any quadrilateral when four sides and one diagonal are known
I am revising Quadrilaterals for SS1 Technical Drawing. Test me on 4. Construct any quadri
Subscribe to unlock allWAEC prep: Success: constructed quadrilateral closes with an error of less than 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Success: sides of the heptagon equal within 0.5 mm by at least two of the three methods
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allWAEC prep: Success: all six diagram pairs correctly judged with a valid geometric reason for each
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 2. Construct a tangent to a circle at a point on its circumference and from an external point
You are my personal SS1 Technical Drawing tutor. Teach me 2. Construct a tangent to a circ
Subscribe to unlock allWAEC prep: Constructing tangents to a point on a circle and to two equal and unequal circles
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 2. Plot the locus of a point on a rotating and a sliding mechanism
Be my SS1 Technical Drawing teacher for this one point: 2. Plot the locus of a point on a
Subscribe to unlock allQuiz: 1. Define and distinguish the ellipse, cycloid, trochoid, involute and helix
I am revising Special Curves for SS1 Technical Drawing. Test me on 1. Define and distingui
Subscribe to unlock allWAEC prep: Constructing an ellipse by three methods and a cycloid
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allWAEC prep: Preparing pyramid and cone developments
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Prepare the pattern development of a prism and of a cylinder
Be my SS1 Technical Drawing teacher for this one point: 1. Prepare the pattern development
Subscribe to unlock allTeach me: 1. Explain orthographic projection and distinguish first-angle from third-angle projection
You are my personal SS1 Technical Drawing tutor. Teach me 1. Explain orthographic projecti
Subscribe to unlock allQuiz: 2. Draw and interpret the first-angle and third-angle projection symbols
I am revising Orthographic Projection for SS1 Technical Drawing. Test me on 2. Draw and in
Subscribe to unlock all