Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →296 prompts matching "Rod at an angle to both card planes and rotates it into a position parallel to t"
Practice set: Finding the intersection of two given planes
Act as my SS3 Technical Drawing tutor. Give me five practice questions on finding the inte
Subscribe to unlock allQuiz: The centroid of a rectangle and a triangle
Act as my SS3 Technical Drawing tutor and quiz me on the centroid of a rectangle and a tri
Subscribe to unlock allSpot my mistake: Assuming a single set square will give every angle a drawing requires
Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a single set squar
Subscribe to unlock allSpot my mistake: Placing the plan above the front view in first angle projection
Act as my SS3 Technical Drawing tutor. Write a short answer on placing the plan above the
Subscribe to unlock allSpot my mistake: Developing the curved surface of a cone as a rectangle of the same height
Act as my SS3 Technical Drawing tutor. Write a short answer on developing the curved surfa
Subscribe to unlock allSpot my mistake: Showing the steps of an offset cutting plane as lines in the sectional view
Act as my SS3 Technical Drawing tutor. Write a short answer on showing the steps of an off
Subscribe to unlock allSpot my mistake: Leaving hidden detail out of a first angle view because it cannot be seen
Act as my SS3 Technical Drawing tutor. Write a short answer on leaving hidden detail out o
Subscribe to unlock allSpot my mistake: Assuming a line inclined in both views can have its true length measured in either
Act as my SS3 Technical Drawing tutor. Write a short answer on assuming a line inclined in
Subscribe to unlock allTeach me: The A2 ISO drawing board and how the sheet is fixed to it
You are my personal SS3 Technical Drawing tutor. Teach me the A2 ISO drawing board and how
Subscribe to unlock allLet me explain: Compasses, dividers and the protractor
I have just studied compasses, dividers and the protractor in my SS3 Technical Drawing cla
Subscribe to unlock allTeach me: The types of line in BS 1192 and what each means
You are my personal SS3 Technical Drawing tutor. Teach me the types of line in BS 1192 and
Subscribe to unlock allPractice set: Dividing a stated line into seven equal parts
Act as my SS3 Technical Drawing tutor. Give me five practice questions on dividing a state
Subscribe to unlock allTeach me: What a scale is and how the representative fraction works
You are my personal SS3 Technical Drawing tutor. Teach me what a scale is and how the repr
Subscribe to unlock allWAEC prep: The scale of chords and its use in setting out angles
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allPractice set: Constructing a diagonal scale to a stated RF
Act as my SS3 Technical Drawing tutor. Give me five practice questions on constructing a d
Subscribe to unlock allPractice set: Constructing an irregular polygon from given data
Act as my SS3 Technical Drawing tutor. Give me five practice questions on constructing an
Subscribe to unlock allQuiz: Drawing a tangent to a circle from an external point
Act as my SS3 Technical Drawing tutor and quiz me on drawing a tangent to a circle from an
Subscribe to unlock allLet me explain: Internal and external common tangents to two circles
I have just studied internal and external common tangents to two circles in my SS3 Technical Drawing class. Let me explain it back to you in my own words, then tell me plainly what I got wrong or left out. Ask me one follow-up question afterwards to test whether I really understood it.
launch and paste in:
WAEC prep: Applying tangency to a spanner or anchor outline
Act as a WAEC/NECO Technical Drawing examiner. I am in SS 3. Set me five exam-style questi
Subscribe to unlock allTeach me: What a locus is and how one is plotted
You are my personal SS3 Technical Drawing tutor. Teach me what a locus is and how one is p
Subscribe to unlock all