Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Rod at an angle to both card planes and rotates it into a position parallel to t"
Teach me: 1. Arrange an appropriate working area before starting a drawing
I am an SS1 student studying Board Practice: Title Block and Lettering in Technical Drawin
Subscribe to unlock allSpot my mistake: 4. Produce single-stroke vertical and inclined Gothic letters
Give me a wrong or muddled explanation of 4. Produce single-stroke vertical and inclined G
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allTeach me: 1. Define an angle
I am an SS1 student studying Angles and Triangles I in Technical Drawing. Explain 1. Defin
Subscribe to unlock allQuiz: 2. Identify the types of angles: acute, right, obtuse, reflex, complementary and supplementary
Set me a quick recall test on 2. Identify the types of angles: acute, right, obtuse, refle
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allSpot my mistake: 4. Construct any acute angle using the tangent and the sine methods, and bisect a given angle
Give me a wrong or muddled explanation of 4. Construct any acute angle using the tangent a
Subscribe to unlock allTeach me: 1. Define a triangle
Be my SS1 Technical Drawing teacher for this one point: 1. Define a triangle. Start with w
Subscribe to unlock allQuiz: 2. Classify triangles by sides
Quiz me on 2. Classify triangles by sides, from the SS1 Technical Drawing topic Angles and
Subscribe to unlock allTeach me: Given one side and two angles
You are my personal SS1 Technical Drawing tutor. Teach me given one side and two angles, a
Subscribe to unlock allLet me explain: 1. Inscribe a circle in a given triangle
I am going to explain 1. Inscribe a circle in a given triangle to you, as an SS1 Technical
Subscribe to unlock allSpot my mistake: 2. Circumscribe a circle about a given triangle
Give me a wrong or muddled explanation of 2. Circumscribe a circle about a given triangle
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allTeach me: 1. Describe the concept of enlargement and reduction of a plane figure
Be my SS1 Technical Drawing teacher for this one point: 1. Describe the concept of enlarge
Subscribe to unlock allLet me explain: 3. Explain why triangles on the same base and between the same parallels are equal in area
I am going to explain 3. Explain why triangles on the same base and between the same paral
Subscribe to unlock allQuiz: 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism
Quiz me on 3. Plot the locus of a point on a simple crank-and-connecting-rod mechanism, fr
Subscribe to unlock allPractice set: Success: both folded models close with a gap of less than 2 mm
Set me five practice tasks on success: both folded models close with a gap of less than 2
Subscribe to unlock allTeach me: 1. Explain orthographic projection and distinguish first-angle from third-angle projection
You are my personal SS1 Technical Drawing tutor. Teach me 1. Explain orthographic projecti
Subscribe to unlock allPractice set: First- and third-angle projection compared
Set me five practice tasks on first- and third-angle projection compared, at the level exp
Subscribe to unlock allTeach me: 1. State the rules and conventions of dimensioning
I am an SS1 student studying Methods of Dimensioning in Technical Drawing. Explain 1. Stat
Subscribe to unlock all