Technical Drawing
AI prompts for senior secondary learners.
📅 36-Week WAEC Study Guide for Technical Drawing →228 prompts matching "Drawing a foundation detail in section"
Quiz: 2. Produce lines with the correct weights
I am revising Lines and Line Work for SS1 Technical Drawing. Test me on 2. Produce lines w
Subscribe to unlock allLet me explain: 3. Draw parallel and perpendicular lines using T-square and set squares
Let me talk you through 3. Draw parallel and perpendicular lines using T-square and set sq
Subscribe to unlock allSpot my mistake: 4. Divide a straight line into any number of equal segments and into a given ratio
Write a short SS1 Technical Drawing answer about 4. Divide a straight line into any number
Subscribe to unlock allReal-life Nigeria: Each line type against the standard line chart. Students produce a reference sheet showing all
Show me how each line type against the standard line chart. Students produce a reference s
Subscribe to unlock allWAEC prep: Success: division into seven parts accurate to within 0.5 mm across the whole line
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allTeach me: 1. Define an angle
I am an SS1 student studying Angles and Triangles I in Technical Drawing. Explain 1. Defin
Subscribe to unlock allLet me explain: 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 120° using compasses only
I am going to explain 3. Construct the special angles 30°, 45°, 60°, 75°, 90°, 105° and 12
Subscribe to unlock allTeach me: 1. Define a triangle
Be my SS1 Technical Drawing teacher for this one point: 1. Define a triangle. Start with w
Subscribe to unlock allQuiz: 4. Construct a triangle equal in area to a given quadrilateral and locate the centroid
I am revising Angles and Triangles II for SS1 Technical Drawing. Test me on 4. Construct a
Subscribe to unlock allLet me explain: 1. Describe a circle
Let me talk you through 1. Describe a circle from the Circles and Triangles I topic. When
Subscribe to unlock allTeach me: 3. Distinguish eccentric from concentric circles and illustrate each
I am an SS1 student studying Circles and Triangles I in Technical Drawing. Explain 3. Dist
Subscribe to unlock allWAEC prep: Constructing eccentric and concentric circles to specification
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allLet me explain: 1. Inscribe a circle in a given triangle
I am going to explain 1. Inscribe a circle in a given triangle to you, as an SS1 Technical
Subscribe to unlock allQuiz: 4. Explain the geometric basis of each construction using bisectors
Quiz me on 4. Explain the geometric basis of each construction using bisectors, from the S
Subscribe to unlock allPractice set: Incentre construction using angle bisectors
Give me a practice set on incentre construction using angle bisectors for SS1 Technical Dr
Subscribe to unlock allWAEC prep: Success: all three circles tangent or passing through the correct points within 0.5 mm
Act as my WAEC Technical Drawing examiner. I am in SS1. Set me an exam-standard question o
Subscribe to unlock allProject task: Completing a properties table for the six quadrilaterals
Give me a practical task on completing a properties table for the six quadrilaterals from
Subscribe to unlock allTeach me: 3. Interpret and apply the first-angle and third-angle projection symbols
I am an SS1 student studying Drawing Standards and Conventions in Technical Drawing. Expla
Subscribe to unlock allReal-life Nigeria: Standard line-type and abbreviation tables. Students produce a reference sheet showing sheet
Show me how standard line-type and abbreviation tables. Students produce a reference sheet
Subscribe to unlock allPractice set: Sheet sizes and line types
Set me five practice tasks on sheet sizes and line types, at the level expected in SS1 Dra
Subscribe to unlock all